BorMann 034964, Инструкция по эксплуатации, Страница: 9 / 19

EN
WWW.BORMANNTOOLS.COM
9
Assembly
Column and machine foot, Fig. 3
1. Set the machine foot (1) down on the ground or the workbench.
2. Place the column (2) on the base plate so that the holes on the column (2) align with the holes on the base plate (1).
3. Screw the four hexagonal screws (19) to fasten the column into the base plate and tighten them using a hexagon spanner (A).
Removing the rack, Fig.4
In order to install your drill, you must first remove the rack (E)
1. Use an Allen key to remove the ring (F) and pull this off the column (2).
2. Now pull the rack (F) out.
Pre-installing the drilling table holder, Fig.5+6
1. Push the crank holder (20) through the hole in the drilling table holder (18) from the inside.
2. Put the crank handle (17) on the crank holder and use the Allen key (3) to secure the crank handle (17).
Installing the drilling table holder, Fig.7+8
1. Insert the rack (E) into the groove on the drilling table holder (18).
2. Align the rack (E) centrally in relation to the drilling table holder (18).
3. When bringing the rack (E) together within the groove, ensure that the tooth meshing between the rack and the drilling table holder (18) is correct.
4. Now place the drilling table holder (18) with the rack (E) on the column (2) and guide the rack (E) into the bottom rack guide on the column foot.
5. Use the ring (F) to secure the rack (E). Ensure that the rack guide on the ring (F) is pointing downwards.
Tighten the integrated Allen screw to affix the ring (F).
6. Screw one of the clamping handles (3) into the drilling table holder (18).
Installing the drilling table, Fig.9
1. Insert the drilling table (4) into the drilling table holder (18).
2. Use a clamping handle (3) to secure the drilling table (4).
3. Insert the roller support (13) into the receptacle on the drilling table (4) and use the wing screws (21) to secure it.
Installing the machine head and column, Fig. 10
1. Place the machine head (14) on the column (2).
2. Align the drill’s spindle with the table and the base plate and tighten the Allen screw that is located on the side of the machine head.
Installing the handles, Fig. 11+12
1. Screw three handles (10) tight in the handle bracket’s thread. Use the hexagon spanner (A) to do this.
2. Screw the remaining handle (10) into the handle bracket for speed adjustment. Use the hexagon spanner (A) to do this.
Installing the folding swarf protector and the drill chuck, Fig.13
1. Push the folding swarf protector (11) onto the spindle on the machine head and use a Phillips head screwdriver to secure it.
2. Push the tapered mandrel (22) into the drill chuck (12) with a sharp jolt.
3. Then push the tapered mandrel (22) into the drill spindle. To do this, guide the drill chuck (12) including the cone (22) into the spindle until is reaches the stop
and then turn it until it slides a little further into the spindle. Now insert the drill chuck (12) including the cone into the spindle. Check that it is tight.
Important: All bare parts are greased in order to protect them from corrosion. Before mounting the drill chuck (12) onto the spindle, both parts must be com-
pletely degreased using an environmentally friendly solvent.
This ensures optimal transmission of power.
Installing the machine
Before you use the drill for the first time it must be mounted in a stationary position on a firm surface. Use both mounting holes in the base plate to do this.
Ensure that the machine is freely accessible for operation, adjustment and maintenance.
Important: The fixing screws may only be tightened to a point where they do not distort or deform the base plate.
Excessive tension can lead to fracture.
Operating instructions
Prior to starting
Ensure that the voltage of the mains supply complies with the specifications on the rating plate. Connect the machine only to a socket with the properly in-
stalled earthing contact. The table drill is equipped with a no-volt trip that is designed to protect the operator from an undesired restart following a drop in
voltage. Should this occur, the machine must be manually restarted.
General instructions (Fig.14)
To switch on the machine, push in the green On button “I” (23); the machine starts up. To switch off , press the red Off button “O” (24); the device shuts down.
Ensure that you do not overload the device.
If the sound of the motor drops in pitch during operation, it is being overloaded.
Do not overload the device to the point where the motor comes to a standstill. Always stand in front of the machine during operation.
Inserting the tool (Fig. 1)
Make sure that the power plug is removed from the socket-outlet before changing tools. Only cylindrical tools with the stipulated maximum shaft diameter
may be clamped in the scroll chuck (12). Only use a tool that is sharp and free of defects. Do not use tools whose shaft is damaged or which are deformed or
flawed in any other way. Use only accessories and attachments that are specified in the operating instructions or have been approved by the manufacturer. If
the pillar drill should become jammed, switch off the machine and return the drill to its starting position.