BorMann 034964, Инструкция по эксплуатации, Страница: 8 / 19

EN
WWW.BORMANNTOOLS.COM
8
Pull out the power plug; Ensure that the mains connection is protected by at least a 10 A-rated fuse.
Avoid unintentional start up; Ensure that switch is turned off when plugging the plug into the socket.
Keep an eye on your work;
A ways keep an eye on your machine and the object you are working on. Never use the machine when you are not concentrating
or are distracted. Never use the machine when you are under the influence Of alcohol or are taking medication.
Check the tool for damage; Before using the tool, safety devices and any slightly damaged parts must be carefully checked to ensure that they are in good
working order, visually examine the tool's power cable on a regular basis. All parts must be correctly assembled and meet all the conditions required to
ensure proper operation.
Unless otherwise specified In the operating instructions, any damaged safety devices and parts must be properly repaired or replaced by a professionally
recognized workshop. Never use tools with defective On/Off switches.
Warning: Using any plug-in tools and accessories other than those specified in these operating instructions can lead to injury.
Maximum workpiece size; Workpieces (max. 20 x 20 cm) may only be processed if they can be clamped securely on the drill table or in the vise.
Remaining hazards
The machine has been built using modern technology in accordance with recognized safety rules. Some remaining hazards however, may still exist.
- Long hair and loose clothing can be hazardous when the work piece is rotating. Wear personal protective gear such as a hair net and tight fitting work
clothes.
- Wood chips and saw dust can be health hazard. Be sure to wear personal protective gear such as safety goggles and a dust mask. Use a vacuum exhaust
system.
- Thrown work-pieces lead to injury if the work piece is not properly secured fed, such as working without a limit stop,
- the use of incorrect or damaged mains cables can lead to injuries caused by electricity,
- even when all safety measures are taken, some remaining hazards which are not yet evident may still be present.
Remaining hazards can be minimised by following the instructions in “safety instructions and in the entire operating manual.
Keep this safety information in a safe place.
Technical Data
Voltage/Frequency: 230V/50Hz
Power: S1 550W
Speed settings: Variable Drilling Speed, 450~2580rpm
Chuck type/size: Keyless chuck/3-16mm
Spindle travel: 80mm
Swing: 300mm
Column Dia.:
65mm
Table tilt: 0-45° left or right
Table size: 240×240 mm with extension support
Base size: 410X250mm
Max. Drill Capacity: 16mm
Machine Height: 950mm
* The manufacturer reserves the right to make minor changes to product design
and technical specifications without prior notice unless these changes signifi-
cantly affect the performance and safety of the products. The parts described
/ illustrated in the pages of the manual that you hold in your hands may also
concern other models of the manufacturer's product line with similar features
and may not be included in the product you just acquired.
* Please note that our equipment has not been designed for use in commercial,
trade or industrial applications. Our warranty will be voided if the machine is
used in commercial, trade or industrial businesses or for equivalent purposes.
* To ensure the safety and reliability of the product and the warranty validity,
all repair, inspection, repair or replacement work, including maintenance and
special adjustments, must only be carried out by technicians of the authorized
service department of the manufacturer
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Laser
Protect yourself and you environment from accidents using suitable precautionary measures!
• Do not look directly into the laser beam with unprotected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting surfaces and persons or animals. Even a laser beam with a low output can cause damage to the eyes.
• Caution - methods other than those specified here can result in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure to the beam can occur.
• If the mitre saw is not used for an extended period of time, the batteries should be removed.
• The laser may not be replaced with a different type of laser.
• Repairs of the laser may only be carried out by the laser manufacturer or an authorised representative.