BorMann 034964, Инструкция по эксплуатации, Страница: 7 / 19

EN
WWW.BORMANNTOOLS.COM
7
General safety instructions
1. General safety regulations and accident prevention
It is essential that you read the safety regulations and operating instructions in their entirety and follow the information contained therein in order to elimi-
nate the possibility of an accident or potentially dangerous situation from occurring while working with the machine
- Always check the device, the mains cable and the plug before using the device. Only operate the tool when it is in good working order and is not damaged
in any way.
Damaged parts have to be replaced immediately by a qualified electrician.
- Always pull the power plug out of the socket outlet before doing any work on the machine, before changing tools and whenever the machine is not being
used
- To prevent damage to the power cable, always lead the power cable away from the rear of the machine.
- Keep the tools in a safe place and out of the reach of children.
Attention!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic bags, film and small parts! There is a risk of swallowing and suffocation!
Electrical connection
The installed electric motor is completely wired ready tor operation. The customer's
connection to the power supply system, and any extension cables that may be used, must conform with local regulations.
Defective electrical connection cables
Electrical connection cables often suffer insulation damage.
Possible causes are:
Pinch points when connection cables are run through window or door gaps.
Kinks resulting from Incorrect attachment or laying of the connection cable.
Cuts resulting from running over the connecting cable.
Insulation damage resulting from forcefully pulling out of the wall socket.
- Cracks through aging of insulation.
Such defective electrical connection cables must not be used as the insulation damage makes them extremely hazardous.
Check electrical connection cables regularly for damage. Make sure the cable is disconnected from the mains when checking.
Electrical connection cables must comply with the regulations applicable in your country.
Warning: The machine must have an earth Cable to protect the operator from electrical shocks.
2. Special safety instructions
- intended use
This drill is designed for drilling metal, plastic, wood and similar materials.
Food and harmful materials may not be processed with the equipment the drill chuck is
only designed for use with drill bits and tools with a shaft diameter of 1.5 To 13 mm. And for cylindrical tool shanks. The equipment is intended for use by
adults only.
The equipment is allowed to be used only for the prescribed purpose. Any other use is deemed to be a case of misuse, the user/operator and not the
manufacturer will be liable for any damage or injuries of any kind resulting from such misuse, please note that our equipment has not been designed for
use in commercial, trade or industrial applications. Our warranty will be voided if the equipment is used in commercial, trade or industrial businesses or for
equivalent purposes.
The pillar drill was designed in such a way so as to all but eliminate potential hazards when the machine is properly used. However. There are a few safety
precautions to observe in order ta ensure that all residual hazards are ruled out.
Ensure proper voltage; the voltage must comply with the specifications an the rating plate.
Use a socket-outlet with earthing contact; the device may only be operated from an cutlet with the properly installed earthing contact.
Extension cable; the cord cross section of an extension cable must measure at least 1.5mm2. Always completely unwind a cable reel prior to use, check the
cable far defects.
Protection against electrical shock;
keep the device away from moisture the device must neither be damp nor be operated n a humid environment. Prior to
every use, check the device and the mains cable with plug for damage. Avoid bodily contact with earthed parts e.g. Pipes, heat elements, etc.
Protection against fire and explosion ; there are spark producing components inside the device. Do not use the device in the vicinity of combustible liquids or
gases. Otherwise there is a risk of fire or explosion.
Handle the device with care; do not use the cable to pull the plug out of the socket. Protect the cable from heat, and sharp edges keep your tools sharp and
clean so that you can work efficiently and safely. Follow the maintenance regulations and the instructions for changing tools.
Wear suitable work clothes and personal protection equipment; loose clothing s not suitable. As can be caught by moving parts, causing to become entan-
gled. Wear a hair net it you have long hair. As a general rule, jewellery should not be worn when working with machine tools. Ensure that you wear safety
goggles. Not doing so could result in eye injury.
Keep your work area neat and tidy; Disorder in the work area can easily lead to accidents. Do not leave any tools, objects, or cable in the direct vicinity of
the work area, as this poses a tripping hazard. Ensure that there is sufficient lighting.
Watch out for other persons; Watch out for other persons (especially children) when using the device, and keep them away from your work area. DO not let
anyone touch the device or the power cable.
Store the tools in a safe location; Store unused devices in a dry, locked location that is out of the reach of children.
Avoid overloading the device; Operate the device only within the specified output range. Do not use any low-powered machines for heavy duty work. Do not
use tools to perform work for which they were not intended.
Maintain a steady foothold; Ensure that you maintain a steady foothold while working. Avoid abnormal body positions and always keep your balance.
Pull out the mains plug; pull Out the mains plug when not using the tool, prior to maintenance, and when changing the drill bit.