Bordignon DTAP 1, Инструкция по эксплуатации, Страница: 8 / 56

4
Direct Drive tapping unit with touch screen multiple control panel
ACCEssINg FUNCTIONs wITH A PAsswOrD
The touch screen on the panel may display a locked or unlocked padlock (FIG. 6). By
pressing on this symbol the operator will see a page designed to enter passwords
which allow access to some functions (FIG. 4).
USER, SUPER USER, OPTIONALS and MAINTENANCE boxes (FIG. 4) will change
colour from grey to green according to the entered passsword and enabled
functions. See following TABLE 1.
taBlE 1
ATTENTION! Access to sET UP and sErVICE menu, which will be explained in the following paragraphs, requires
the padlock to be unlocked by password 1234.
Manufaturer recommends locking the padlock again using password 1111, after setting the threading program.
PAsswOrD PADLOCk FUNCTIONs
USER
On
Off
1111
On/off
Change of tap
SUPERUSER
On
Off
12345*
Set up
Service
OPTIONALS
On
Off upon
request
Right-left threading
Thread checker (D-TC)
Automatic pressure regulator (D-APR)
Storage usb key (D-USB)
Return speed
MAINTENANCE
On
Off not
available
Maintenance (manufacturer only)
INsTALLINg
1.
2.
3.
4.
5.
Place the tapping unit and align it carefully to the hole. Secure it in position with 4 screws and 2 pins (see dimensions
and position on pages 26-27-28);
Connect the tapping unit socket into the plug E (FIG. 1) of the control panel. The serial number of the tapping unit and
serial number of the panel must be the same. The serial number is printed on the back of the tapping unit and on the
right side of the panel.
Connect the compressed air to the panel with a 8 mm pipe (F - FIG. 1). The air pressure should be as follows:
M2 = 2 BAR
M3 - M4 = 3 BAR
M5 - M6 = 4 BAR
M8 or bigger= 5-6 BAR
Make wire connections on socket D (FIG. 1):
start signal and other desired connectios such as: electrovalve for
lubrication, alarm to the press, end of cycle signal, external emergency system . Follow instructions on pages 13-
23-33-43 of the wiring diagram attached to this manual;
Connect the control panel to power supply 400 V AC 50-60 Hz.
FiG. 4
INSTALLING:
Start signa electrovalve for lubrication ,
alarm to the press, end of cycle signal, external emergency system
Connect the control panel to power supply 230 V AC 50-60 Hz
ACCESSING FUNCTIONS WITH A PASSWORD
ATTENTION: Access to SET UP and SERVICE menu, which will be explained in the following paragraphs, requires the
padlock to be unlocked by password 1234.
1- Place the tapping unit and align it carefully to the hole. Secure it in position with 4 screws and 2 pins (see dimensions and
position on pages 18-19-20)
2- Connect the tapping unit socket into the plug D ( fig.1) of the control panel. The serial number of the tapping unit and serial
number of the panel must be the same. The serial number is printed on the back of the tapping unit and on the right side of the
panel.
3- Connect the compressed air to the panel with a 6 mm pipe (E - fig. 1).
The air pressure should be as follows:
M2 = 2 bar
M3- M4 = 3 bar
M5- M6 = 4 bar
M8 or bigger= 5-6 BAR
4- Make wire connections on socket C (fig. 1): l and other desired connectios such as:
. Follow instructions on pag. 4 of the wiring diagram
attached to this manual
5-
The touch screen on the panel may display a locked or unlocked padlock (fig. 6).
By pressing on this symbol the operator will see a page designed to enter
passwords which allow access to some functions (fig.4).
USER, SUPER USER, OPTIONALS and MAINTENANCE boxes (fig.4) will
change colour from grey to green according to the entered passsword and
enabled functions. See following table 1
Manufaturer recommends locking the padlock again using password 1111, after setting the threading program.
NEVER CONNECT PANEL AND TAPPING
UNIT WITH DIFFERENT SERIAL NUMBER!
4
serial n°
ON/OFF
CHANGE OF TAP
SET UP
SERVICE
RIGHT-LEFT THREADING
upon THREAD CHECKER (D-TC)
re que s t AUTOMATIC PRESSURE REGULATOR (D-APR)
STORAGE USB KEY (D-USB)
RETURN SPEED
not MAINTENANCE
a va i l a bl e (MANUFACTURER ONLY)
FUNCTIONS
USER
SUPERUSER
MAINTENANCE
1111
1234
PASSWORD
OPTIONALS
PADLOCK
table1
on
off
on
off
on
off
on
off
Fig. 4
SUPER
USER
OPTIO
NALS
0
NEVER CONNECT PANEL AND TAPPING UNIT
WITH DIFFERENT SERIAL NUMBER!
serial nr.
* Super User password can be modified following instructions on page 12