background image

90 mm

24 mm

2

Wood dowel  (6x50mm)

6mm

Main wing joiner

1

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

B'

B

C = C '

B = B '

Make sure to glue securely.

If not properly glued, a failure in flight may occur.

Temporarily fasten down the main wing and 

check its correct position.

Securely glue together.If coming off during flights,

you'll lose  control of your airplane which leads 

to accidents!

C'

C

6.2mm

Blind Nut

2

2

Blind Nut (6mm)

Screw(6x50mm)

90 mm

25 mm

6mm

Epoxy the main wing together.

Drill holes at appropriate position in the wing for 

fetching out the servo line and air pipe.  

Drill two holes to appropriate position in the

wing and epoxy  the wood dowel in it.

Assemble the main wing separately and

be sure with the right way.

Mount the main wing to the fuselage.

Drill two holes to relevant position in the fuselage

for installing  the main wing.

17

18

19

20

21

4

16

Fuel tank (550cc) 1

Linkage Stopper

Washer (2mm)

 Washer (2mm)

Nut (2mm)

Set screw (3x4mm)

Washer (2mm)

Set screw (3x4mm)

1

1

1

1

Fuel supply line

Fuel spray line

Air pressure line

Set Screw (3x4mm)

Set Screw (2mm)

Rod (2x400mm)

Set Screw (2mm)

Washer (2mm)

Linkage Stopper

1

1

1

1

1

4

4

Washer (4x8mm)

4

Rod (2x400mm)

Blind Nut (4mm)

Screw (4x25mm)

Set Screw (3x4mm)

Assemble the servo and switch.

Mount the servo and switch in the fuselage.

Assembly of the fuel tank.

Mount the fuel tank into the fuselage.

Assemble the accelerator push rod to nose engine.

Assemble the accelerator push rod to nose engine.

 

 

 

44

45

46

47

48

43

Содержание A-36









Отзывы: