Bomedent iRoot pro Скачать руководство пользователя страница 28

Страница: 28 / 40

8. Error code

Error code

Error

Cause

Check Remedy

When

working

E-0

Self-Check error

Malfunction of circuit

Contact your dealer

E-1

Overcurrent

The motor handpiece is

locked. (auto reverse

mode)

Remove payload

E-2

Overvoltage

Malfunction of circuit

Contact your dealer

When

Charging

E-3

Charger failure

Malfunction of circuit

Contact your dealer

E-4

Low voltage of battery

Battery out of service

Chang Battery

E-5

High voltage of battery

Battery out of service

Chang Battery

E-8

Low voltage of adaptor

Adaptor out of service

Change adaptor

E-9

High voltage of adaptor

Adaptor out of service

Change adaptor

When

calibration

E-7

Calibration failure

Motor damaged or

handpiece blocked

Replace the motor

handpiece or motor

9. Troubleshooting

If your device

does not seem to work properly, it does not necessarily mean that the central unit does

not work correctly. Please first review the below checklist in order to exclude any user error or

anatomic/other peculiarities before contacting your dealer.

If the problem persists please contact either your local dealer or manufacturer.

Problem

Cause

Solution

The power is unable to turn

on.

Battery has fully discharged.

Recharge the battery.

No battery inserted.

Insert battery.

The internal fuse has burnt.

Contact your dealer.

Charge failure

Battery has been completely discharged.

Replace with new battery.

The power cord plug is not inserted into the

outlet

Plug the power cord or adaptor properly

The motor handpiece is not correctly set to the

charger

Insert the power cord plug into the outlet.

There is some residual contamination on the

charger base

Remove the residual contamination

An error code is displayed.

Refer to No. 8Error Code.

Nothing is displayed on the panel of the

handpiece even when it is set to the charger

Contact your dealer.

The charger out of service

Charge the motor by cable, then contact

your dealer

The motor hand piece

does not rotate.

The contra angle has been blocked

Clean or reset the contra angle

The alarm sounds when the

motor is working

The contra angle head has jammed up.

Clean the contra angle head

Содержание iRoot pro









































Результаты поиска

Содержание iRoot pro

Отзывы:

Похожие инструкции для iRoot pro

Бренды по названию

Популярные бренды

Bomedent iRoot pro, Руководство по эксплуатации

Результаты поиска

Содержание iRoot pro

Отзывы:

Похожие инструкции для iRoot pro

Бренды по названию

Популярные бренды