BOMANN EHBC 556 IX Скачать руководство пользователя страница 6

Страница: 6 / 20

NOTE

NOTE: : : : Recommandations!

Recommandations!

•

Wear protective gloves to avoid injuries at
ble sharp edges.

•

When carrying the appliance use the
handles at the housing sides.

•

Hob and oven must be from the same manufa
turer and marked with the same type designation.

•

The appliance conforms to the heat insulation
class Y, i.e. only one side of the appliance may be
installed near higher kitchen furniture or walls.

•

Make sure that the oven and the hob are located
centrally to each other.

•

The distance between the hob and a
hood must be at least as large as specified in the
instructions of the extractor hood!

•

Install the appliance so that all controls
to reach and the appliance door can open without
being impeded.

Cabinet o

Cabinet opening and appliance

pening and appliance

pening and appliance dimensions

dimensions

Prepare the
cabinet opening
according to the
dimensional
drawings.

Preparing the worktop for

Preparing the worktop for installation of the hob

installation of the hob

CAUTION:

Before cutting secure the outer cutout
adhesive tape to avoid traces of jigsaw on the
top.

•

The worktop must be leveled horizontally and are
sealed to the wall side against overflowing liquids
or moisture.

ctive gloves to avoid injuries at possi-

appliance use the recessed

Hob and oven must be from the same manufac-
turer and marked with the same type designation.
The appliance conforms to the heat insulation
class Y, i.e. only one side of the appliance may be
installed near higher kitchen furniture or walls.
Make sure that the oven and the hob are located

The distance between the hob and an extractor
hood must be at least as large as specified in the
instructions of the extractor hood!

so that all controls are easily

the appliance door can open without

dimensions

Figures in mm

installation of the hob

cutout edge with wide

adhesive tape to avoid traces of jigsaw on the work-

leveled horizontally and are

sealed to the wall side against overflowing liquids

•

The cut surfaces (cutout e
with special varnish, silicone rubber or cast raisin
in order to prevent swelling caused by humidity.

•

Clean and dry the worktop in the cutout area
thoroughly.

Worktop cutout

Prepare the cutout of
the worktop according
to the dimensional
drawing.

Installing

Installing the hob

the hob

1111     Hob
2222     Gasket
3333     Worktop

4(a)

4(a) Mounting clip
4444((((bbbb)))) Mounting bracket

5555 Screw (4 pcs

NOTE

NOTE::::

With a worktop thickness of 30 to 40 m
mounting clips 4(a). The front
by the mounting brackets 4(b) with a worktop thic
ness of 28 mm.

•

First check the factory fitted hob seal
frame to the integrity and the proper fit.

•

Place the hob according to the hob
"Appliance Overview" and with the connecting c
ble first centrally into the prepared cutout of the
worktop. Make sure that the distances to the cu
ting are equal on all four sides and that the seal is
resting on the worktop.

•

Fix the hob depending on the worktop thickness
by attaching the enclosed
the hob bottom at the provided holes and fasten
them with the screws.

The cut surfaces (cutout edges) must be sealed

silicone rubber or cast raisin

in order to prevent swelling caused by humidity.
Clean and dry the worktop in the cutout area

Figures in mm

Hob
Gasket
Worktop
Mounting clip**** (4 pcs)
Mounting bracket**** (2 pcs)
Screw (4 pcs)

With a worktop thickness of 30 to 40 mm using the

(a). The front clips must be replaced

b) with a worktop thick-

First check the factory fitted hob seal at the hob
frame to the integrity and the proper fit.

the hob according to the hob drawing under