•
Open the door completely.
•
Push the folding clamps o
•
Slightly
•
When reinstalling the door, m
with the protrusion of the hinge holder.
•
Then press down the f
Then press down the f
Then press down the f
Then press down the folding clamps again,
olding clamps again,
olding clamps again,
olding clamps again,
oven door.
Reverse the bulb
Reverse the bulb
Reverse the bulb
Reverse the bulb
WARNING
WARNING
WARNING
WARNING::::
Allow the lamp to cool down before replacing the bulb.
•
Use the correct bulb, heat resistant
•
Unscrew the lamp cover anti
•
Replace the bulb and make sure that the lamp is properly seated in the socket.
•
Reattach the lamp cover
•
Check the functionality of the lighting.
Before you contact a
Before you contact a
Before you contact a
Before you contact annnn authorized
authorized
authorized
authorized sssspecialist
pecialist
pecialist
pecialist
Problem
Problem
Problem
Problem
Possible causes
Possible causes
Possible causes
Possible causes
Appliance does not
work.
The power supply is
ed.
The upper part of food
is too dark and the low-
er one is too light.
Not enough lower heat.
The lower part of food is
too dark and the upper
one is too light.
Too much lower heat.
The food is done on the
outside but not on the
inside.
Temperature too high.
The oven lamp does not
work.
The bulb is defective,
inserted incorrectly or not firmly.
NOTE:
NOTE:
NOTE:
NOTE:
If a problem still persists after following the steps above, contact your distributor or an
16
Open the door completely.
Push the folding clamps of the hinges on both sides upwards.
close door and then lift it up to remove it.
When reinstalling the door, make sure the notch of the hinge is properly aligned
with the protrusion of the hinge holder.
olding clamps again,
olding clamps again,
olding clamps again,
olding clamps again, otherwise the hinges could get damaged when
before replacing the bulb. There is risk of burns!
There is risk of burns!
There is risk of burns!
There is risk of burns!
Use the correct bulb, heat resistant up to 300°C: 1 x 25 W (type E14, halogen)
1 x 25 W (type E14, halogen)
1 x 25 W (type E14, halogen)
1 x 25 W (type E14, halogen)
cover anti-clockwise and clean it with a dry cloth.
Replace the bulb and make sure that the lamp is properly seated in the socket.
Reattach the lamp cover and screw tightly.
Check the functionality of the lighting.
Troubleshooting
Troubleshooting
Troubleshooting
Troubleshooting
pecialist
pecialist
pecialist
pecialist
Possible causes
Possible causes
Possible causes
Possible causes
What to do
What to do
What to do
What to do
The power supply is disconnect- Check the fuse of your domestic wiring system.
Not enough lower heat.
- Select the upper/lower heat function.
- Use a deeper baking dish.
- Reduce the oven temperature.
- Insert the baking dish into the lowest guide rail.
Too much lower heat.
- Select the upper/lower heat function.
- Use a deeper baking dish.
- Reduce the oven temperature.
- Insert the baking dish into a higher guide rail.
Temperature too high.
Reduce the oven temperature and increase the
cooking time.
The bulb is defective, has been
inserted incorrectly or not firmly.
Check the bulb, see “Reverse the bulb”.
If a problem still persists after following the steps above, contact your distributor or an
f the hinges on both sides upwards.
ake sure the notch of the hinge is properly aligned
inges could get damaged when closing the
clean it with a dry cloth.
Replace the bulb and make sure that the lamp is properly seated in the socket.
our domestic wiring system.
eat function.
Use a deeper baking dish.
Reduce the oven temperature.
Insert the baking dish into the lowest guide rail.
eat function.
Use a deeper baking dish.
Reduce the oven temperature.
Insert the baking dish into a higher guide rail.
Reduce the oven temperature and increase the
see “Reverse the bulb”.
If a problem still persists after following the steps above, contact your distributor or an authorized technician.
