manualshive.com logo in svg

Bolt VC-310N, Руководство пользователя, Страница: 13 / 40

Поделиться
Скачать
Bolt VC-310N Скачать руководство пользователя страница 13

Turning On the Flash and Firing a Test Shot 

|

 13

Overheating protection mode:

 If the operating temperature of the VC-310N is too high after several full-power 

flashes, the flash will enter the overheating protection mode. The thermal warning indicator [TP-HI] will appear 
on the LCD, and you should let the flash cool down for a period of 2–5 minutes.

Default setting:

 You can restore the flash to its original settings. To do this, first make sure the flash is off. Press 

and hold the Test and Power buttons for 3 seconds, then release. 

LED preview and focusing:

 There are three LEDs built into the flash head that can be used as a preview light 

to illuminate the subject for reference, or as an autofocus assist light to help the camera focus when the scene 
is too dim.

To use the LEDs as a preview light, press the power button while the flash is on. To turn the preview light off, 
press the power button again. 

The LEDs will function as an autofocus assist light whenever you press the camera’s shutter release halfway.

Modeling flash:

 The modeling flash fires a burst of several flashes to show you where unwanted shadows 

occur in your setup. Press and hold the Test button for more than two seconds.

Содержание VC-310N









































Отзывы:

Нет отзывов