manualshive.com logo in svg

Bolondi SW 060-CF.09, Инструкция по эксплуатации

Поделиться
Скачать
Bolondi SW 060-CF.09 Скачать руководство пользователя страница 7

2)  RECEIVING AND UNPACKING

2.1)  CHECKING  AND UNPACKING

2.1.1)  On receipt, make sure that the model and technical specifi cations correspond with 
the order.

2.1.2)  Make sure that goods were not damaged during transport.

2.1.3)  Any damage found when the goods are received must be documented and the 
sender informed within 3 days of receipt.

2.1.4)  Disposal of packaging: the purchaser is responsible for following the correct pro-
cedure and applicable regulations in their country for disposing of the consumables and 
refuse created by unpacking the product.

                  

INSTRUCTIONS FOR CORRECT WASTE MANAGEMENT.

                  Material: Paper and cardboard    

(

EWC code 15 01 01

)

                  Plastic  

 

 

 

(

EWC code 15 01 02

)  

                  Wood   

 

 

 

(

EWC code 15 01 03

)  

2.2)  DEMOLITION AND DISPOSAL

It is the purchaser’s responsibility to follow the correct procedure and comply with the current 
laws in force in his country as regards to disposing of consumables and materials resulting 
from demolition.
Please remember that by waste is meant any substance or object under obligation of dispo-
sal.
According to their origin and pursuant to the above mentioned Decree, waste products are 
classifi ed as urban or special waste and, depending on their dangerous characteristics, as 
hazardous or non-hazardous waste.
Waste resulting from the demolition of the machine is classifi ed as special waste.

WARNING! It is forbidden to mix together diff erent categories of hazardous waste and 
hazardous waste with non-hazardous waste.

INSTRUCTIONS FOR THE MOST APPROPRIATE HANDLING OF WASTE.

Ferrous materials (EWC code 17 04 05)

As this is recyclable material (secondary raw materials), it should be taken to an authorised 
collection centre.

Plastic materials (EWC code 16 02 16)

Recycling permitted where landfi ll disposal is performed for urban-type waste.
Incineration permitted in plants equipped with post-combustion and fl y-ash capture systems.
Follow applicable national legislation, as amended.

(02-000-00-EN)

SW 060-CF.09-MANUAL Rev.00

7

Содержание SW 060-CF.09





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды