background image

50 Spring Street, Ramsey, NJ 07446, U.S.A.

Tel. 201-934-8500 • Fax: 201-934-9832

www.bogen.com

Limited Warranty; Exclusion of Certain Damages

Accessories/Components

1

. One of the following two back boxes are required for assembly.

BBF - Flush-Mount Back Box

Mounting kit for installing amplifier flush to a wall

BBS - Surface-Mount Back Box

Mounting kit for installing amplifier to the surface of a wall

2. The WMAD is required for assembly.

WMAD - Front Cover / Door

Prevents tampering with system settings

Simple installation

RVCP - Remote Volume Control Panel

Push-button operation of motorized master volume 
control

Fits in standard single gang electrical box

Decora style cover plate

BBF

BBS

WMAD

The following item is an optional accessory.

Mounting Components

Accessories

RVCP

The 

Bogen Power Vector Amplifiers

are warranted to be free from defects in material and workmanship for three (3) years from the date of sale to

the original purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes defective (as confirmed by
Bogen upon inspection) during the applicable warranty period, will be repaired or replaced by Bogen, at Bogen’s option, provided the product is
shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. Repaired or replacement product
will be returned to you freight prepaid. This warranty does not extend to any of our products that have been subjected to abuse, misuse, improper
storage, neglect, accident, improper installation or have been modified or repaired or altered in any manner whatsoever, or where the serial number
or date code has been removed or defaced.

THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER’S SOLE AND EXCLU-
SIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM
EXTENT ALLOWABLE BY LAW. 

Bogen's liability arising out of the manufacture, sale or supplying of products or their use or disposition, whether

based upon warranty, contract, tort or otherwise, shall be limited to the price of the product. 

IN NO EVENT SHALL BOGEN BE LIABLE FOR SPE-

CIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS
OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES.

Some States do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from State to State.

Products that are out of warranty will also be repaired by the Bogen Factory Service Department – same address as above or call 201-934-8500.
The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service Department. All shipping
charges in addition to parts and labor charges will be at the owner's expense. All returns require a Return Authorization number. For most efficient
warranty or repair service, please include a description of the failure.

12/2008

Содержание WV100


















Отзывы: