Boekel InSlide Out 241000 Скачать руководство пользователя страница 7

Страница: 7 / 9

6. Fault Diagnosis

Symptom

Possible Cause

Action Required

1. Unit does not operate

Unit not switched on

Unit not plugged into
power supply

Fuses blown

Power supply failure

Switch on

Plug in, switch on

Replace fuses per 8.2

Check that other electrical
appliances on the same
circuit are working

2. Chamber temperature does

not rise when expected

Actual temperature is
higher than set
temperature

Temperature control
circuit fault

Check set temperature

Have unit checked by
competent person

3. Temperature continues to

rise when not expected

Actual temperature is
lower than set temperature

Temperature control
circuit fault

Check set temperature

Have unit checked by
competent person

4. Slides dry out during

heating cycle

Gasket not sealing

Lid bent

Insufficient buffer placed
in bottom of tray

Latch not fully engaged

Replace Tray and Gasket
Assembly

Replace Lid

Place more buffer in
bottom of tray

Re-install Tray Assembly
into chamber and re-
tighten Latch

7. Technical Specifications

This equipment is intended for indoor use and will meet its performance figures within the
ambient temperature range of 10

C to 35

C, with maximum relative humidity of 80% (non-

condensing).

Installation Category II (transient voltages). Pollution Degree 2 in accordance

with IEC 664. Suitable for operation at altitudes of up to 6500 feet.

Содержание InSlide Out 241000










Результаты поиска

Содержание InSlide Out 241000

Отзывы:

Бренды по названию

Популярные бренды

Boekel InSlide Out 241000, Руководство по эксплуатации

Результаты поиска

Содержание InSlide Out 241000

Отзывы:

Бренды по названию

Популярные бренды