background image

3. THE COOL DOWN PHASE

This stage is to let your Cardio Vascular System and muscles wind down. This is a repeat of the warm up exercise e.g. 

reduce your tempo, continue for approximately 5 minutes. The stretching exercises should now be repeated, again 

remembering not to force or jerk your muscles into the stretch.   

As you get fitter you may need to train longer and harder. It is advisable to train at least three times a week, and if 

possible space your workouts evenly throughout the week. 

MUSCLE TONING 

To tone muscle while on your exerciser you will need to have the resistance set quite high. This will put more strain on 

your leg muscles and may mean you cannot train for as long as you would like. If you are also trying to improve your 

fitness you need to alter your training program. You should train as normal during the warm up and cool down phases, 

but towards the end of the exercise phase you should increase resistance, making you work harder. You may have to 

reduce your tempo to keep your heart rate in the target zone. 

WEIGHT LOSS 

The important factor here is the amount of effort you put in. The harder and longer you work the more calories you will 

burn. Effectively this is the same as if you were training to improve your fitness, the difference is the goal. The calorie 

function is an estimate only and to be used for comparison between workouts.

CARE AND MAINTENANCE 

Proper maintenance is very important to ensure your equipment is always in top working condition. Improper 

maintenance could cause damage or shorten the life of your equipment and void the WARRANTY coverage

Important:

 Never use abrasives or solvents to clean the equipment. To prevent damage to the computer, keep liquids 

away and keep it out of direct sunlight. 

After each workout:

 Wipe off the console and other frame surfaces with a clean, water dampened soft cloth to 

remover excess perspiration. Inspect and tighten all parts of the equipment regularly. Replace any worn parts 

immediately. 
Don’t use the equipment before the worn parts were replaced by new ones. When you feel the exerciser is not 

smooth, please check the status of the parts and if need be call the service hot line. 

EXERCISE

INSTRUCTIONS

18

Содержание ABX190M




















Отзывы: