background image

13

WARNING

PEDALS & CRANKS 

 

(A117BB, ASB500, ASB700 & ASB800)

Given the design and usage of Indoor Cycles it is very important to ensure correct assembly and 
ongoing maintenance for optimum performance and your safety. 
Supplied with the bike is a pedal wrench for your initial assembly.

 (PIC A)

. Please always keep this 

wrench on hand nearby the bike as regular tightening of the pedal is required to keep your bike in 
optimum working condition. 
Pedals are marked as “L” and “R” for left and right side. 

(PIC B)

. The left and right sides are 

determined as if you are sitting on the bike. Please ensure you take care and do not thread the 
pedals into the incorrect side. 

(PIC C)

. This will cause damage to the thread of the pedal and the 

crank. This will require replacement of parts and is not covered under warranty. 
Pedals must also be firmly seated into the crank upon initial assembly and then as part of on-going 
regular maintenance before usage. There should be no gap visible between the crank and the 
pedal spindle. 

(PIC D)

. If there is, you have still not tightened up the pedal enough. Both pedals 

must always be firmly seated right up against the crank.
You must always maintain the bike; pedals must be checked on a regular basis and re-tightened 
before usage to ensure the pedal spindle is right up against the crank. 
Lack of maintenance in this regard can cause the pedal to slightly unwind which will in turn damage 
the thread to the pedal and crank upon further usage. Lack of maintenance and care in this regard 
is not covered under warranty as it is not a manufacturing fault. 
Please read the owner’s Manual carefully and if you have any concerns, please contact our service 
department on 

[email protected]

gpisports.com.au

no gap between edge of

crank and pedal axle

Содержание A117BB

















Отзывы: