BodyCraft BCG-GX Скачать руководство пользователя страница 15

Страница: 15 / 21

STEP 8 INSTALL LOWER CABLE

1. Route the steel ball end of the Lower cable (89) under Pulley L1 mounted at the front of the Low Pull

Station using one 3/8" X 1-3/4" Hex Bolt (101) and one 3/8" Nylon Nut (124).

2. Continue back to Pulley L2 mounted on the Base Frame (1) using one 3/8" X 1-3/4" Hex Bolt (101) and

one 3/8" Nylon Nut (124). Route the cable underneath L2 and then up to Pulley L3 mounted in bottom

of the Double Pulley Block (19) using one 3/8" X 1-3/4" Hex Bolt (101) and one 3/8" Nylon Nut (124).

3. Continue down to Pulley L4 mounted to the Base Frame (1) using one 3/8" X 1-3/4" Hex Bolt (101) and

one 3/8" Nylon Nut (124).

4. Route the cable underneath L4 and Pulley L5 mounted in the slot in the bottom of the Front Upright (3)

using one 3/8" X 3" Hex Bolt (99), two 3/8" washers (116), two 3/8" ID Bushings (77), and one 3/8"

Nylon Nut (124).

5. Connect the steel ball end of the cable to the receptor bracket L6 welded to the Leg Extension Arm (10).

Содержание BCG-GX






















Результаты поиска

Содержание BCG-GX

Отзывы:

Бренды по названию

Популярные бренды

BodyCraft BCG-GX, Инструкция по эксплуатации

Результаты поиска

Содержание BCG-GX

Отзывы:

Бренды по названию

Популярные бренды