background image

BR2998

Page  4

Part Listing

The following parts list describes all of the parts illustrated on the exploded diagram on the following page. 

 

PLEASE NOTE 

: most of these parts are already pre-assembled on your unit.

# Description

01 Main Frame
02 Center Post
03 Left Pedal Tube
04 Right Pedal Tube
05 Left Coupler Bar
06 Right Coupler Bar
07 Pedal Connection Joint
08 Pulse Handle Bar
09 Left Handle Bar
10 Right Handle Bar
11 Front Stabilizer
12 Rear Stabilizer
13 Coupler Bar Axle
14 Crank
15 Bushing
16 Carriage Bolt (M8x70 mm)
17 Pedal Hinge Bolt (φ16x1/2"x97 mm)
18 Bolt (M10x68 mm)
19 Bolt (M8x40 mm)
20 Bolt (M8x20 mm)
21 Bolt (M8x15 mm)
22 Bolt (M8x30 mm)
23 Hex Bolt (M8x45 mm)
24 Hex Bolt (M8x40 mm)
25 Screw (M5x15 mm)
26 Screw (M5x12 mm)
27 Screw (M4x25 mm)
28 Screw (M4x10 mm)
29 Washer (M10)
30 Big Washer (M8)
31 Washer (M8)

# Description

32 Arc Washer (M8)
33 Spring Washer (M8)
34 Wavy Washer (φ16 mm)
35 Wavy Washer (φ19 mm)
36 Nylon Nut (1/2")
37 Nylon Nut (M10)
38 Nylon Nut (M8)
39 Cap Nut (M8)
40 Left Pedal
41 Right Pedal
42 Pulse Handle Bar Cover
43 Left Coupler Bar Cover (Rear)
44 Left Coupler Bar Cover (Front)
45 Right Coupler Bar Cover (Rear)
46 Right Coupler Bar Cover (Front)
47 Rectangular End Cap (25x50 mm)
48 Round End Cap (22 mm)
49 Round End Cap (32 mm)
50 Nylon Bushing (25 mm)
51 Nylon Bushing (32 mm)
52 End Cap for Front Stabilizer
53 End Cap for Rear Stabilizer
54 Foam Grip of Pulse Handle Bar
55 Foam Grip of Handle Bar
56 Monitor
57 Pulse Sensor
58 Monitor Wire (Upper)
59 Monitor Wire (Lower)
60 Adapter
61 Water Bottle Holder
62 Tool 1
63 Tool 2

Содержание BR2998



























Отзывы: