Bodine 3912 Скачать руководство пользователя страница 21

Страница: 21 / 24

www.bodine-electric.com

Figure 8 - Manual Speed

Potentiometer/ Interface Details

Electronic Speed Control

Motor speed can be controlled with a 0 to +10 VDC isolated signal with 0.1 mA

current capability in lieu of the manual speed potentiometer. This speed

control input should be connected to terminal S2 on the control board. The

common side of the signal must also be isolated and connected to terminal

S1 on the main control board.

Logic Signal Control of Braking, Direction of Rotation, and Deceleration

Motor braking (or disable), direction of rotation and deceleration can be

controlled using optically isolated logic signals from a programmable

controller, personal computer, or other electronics.

Exercise extreme caution when using Programmable Logic Controllers (PLCs).

Although some may claim to have optically isolated output modules, their output

commons may be connected to other circuitry either within or connected to the

PLC. In such cases, the PLC outputs should be isolated from the ABL control, by

a relay or by an electronic isolation module, to prevent damage to the PLC or the

ABL control.

If a Programmable Controller with a

relay output module is not available,

AC or DC outputs from the PLC can

be used to drive separate relay coils.

See PLC user’s manual for application

information. See Figure 6 to determine

how to connect relay contacts to the

ABL-3912E and ABL-3913E.

Signal Isolation Using a Bodine

Model 3984 Interface Module:

Follow the installation instructions

provided with the module to isolate

the input signals between the

control electronics and the ABL

Control. See Figure 7 for control

input connections and Figure 8 for

speed control interface details.

WARNING

Never rely on logic circuitry as a means of disabling the motor or control.

To prevent unsuspected mechanical motion and potential injury, the 115

VAC power should always be disconnected whenever logic circuits or

the driven equipment are serviced.

12V

10K

Minimum

Speed

Adjustment

10K

Maximum

Speed

Adjustment

Signal Common

51.1K

Signal Common

100K

10K

–
+

Содержание 3912

























Результаты поиска

Содержание 3912

Отзывы:

Похожие инструкции для 3912

Бренды по названию

Популярные бренды

Bodine 3912, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 3912

Отзывы:

Похожие инструкции для 3912

Бренды по названию

Популярные бренды