manualshive.com logo in svg

Bodine 3912, Инструкция по установке и эксплуатации, Страница: 20 / 24

Поделиться
Скачать
Bodine 3912 Скачать руководство пользователя страница 20

20

www.bodine-electric.com

Remotely Located Braking (Disable), Direction 
of Rotation, andDeceleration Controls

Mechanical switches or relays can be used to switch the control inputs 

shown in Figure 5. Figure 7 shows a schematic representation of manual or 

relay switched inputs.

Contacts

or Relay

Switches

Manual

DECEL

DECLCOM

DIR

DIRCOM

DISCOM

10K

12V

4000 Series CMOS

4000 Series CMOS

12V

10K

4000 Series CMOS

12V

10K

Signal

Common

DISABLE

Figure 7 - Manual Switch and Relay Control Inputs.

The following chart lists the control functions relative to the state of the 

mechanical switches or relays.

Switch

Closed

Open

DISABLE

1

Stop

Run

DIR

2

CW

4

CCW

4

DECEL

3

Decelerate

Accelerate

1.  When the DISABLE switch is closed the motor will be dynamically braked.

2.  A “Smart Reverse Circuit” prevents plug reversing when the DIR switch is 

opened or closed. The motor will brake to a stop before changing direction.

3.  The DECEL switch controls soft stops and starts. The degree of acceleration and 

deceleration can be varied with the trim potentiometers on the control board. 

See Page 14.

4.  The output shafts of gearmotors with odd number of stages (Bodine type 

designations ending with W3, E1, or E3) will rotate in the opposite direction.

Electronic Control Input Connections

Optional Interface Boards are available from Bodine and other manufacturers. 

They provide electrical isolation between the input signal and the brushless 

DC motor control circuitry, and are recommended for motion control 

applications requiring electronic control of motor speed, rotational direction, 

deceleration, and braking.

NOTE: The 
DISCOM, 
DIRCOM, 
DECLCOM, 
S1, and COM 
terminals on the 
control board are 
all connected in 
common.

 

Содержание 3912

























Отзывы:

Нет отзывов