background image

38

On-Line  EXPRESS

Appendix G: Warranty Information

Limited Warranty

Boca Research, Inc. (BRI) warrants to the original buyer of this BRI product that the

hardware is free of defects in materials and workmanship for a period of five (5) years

from the date of purchase from BRI or its authorized dealer. Should the product fail to be in

good working order at any time during the five-year period, BRI, will at its option, repair or

replace this product as described below. This warranty does not cover defects resulting from

misuse, abuse, negligence, accident, repairs, or alterations made by either the customer or

another party. Boca Research reserves full rights to determine whether a defective product

falls into this category.

The entire risk as to the quality and performance of the product rests with the customer.

Any written or oral information or advice given by Boca Research dealers, distributors,

agents, or employees will in no way increase the scope of this warranty. This warranty

applies only to the product described in this manual and not to any other value-added

software which may be included.

All customers are required to demonstrate proof of purchase when requesting a Return

Merchandise Authorization (RMA). The period of service commences on the date of

purchase. A copy of the sales slip must be included with the returned merchandise.

Products which require Limited Warranty service during the warranty period should be

delivered to BRI at the address in the Appendix (Servicing Your Boca Product) with proof

of purchase and the Return Merchandise Authorization (RMA) number provided by BRI

Technical Support. Refer to the Appendix in your manual. Replacement parts or complete
products will be furnished on an exchange basis only. Replaced parts and/or products

become the property of BRI.

If the returned product is sent by mail, the purchaser agrees to prepay shipping charges,

insure the product or assume the risk of loss or damage which may occur in transit, and to

use a shipping container equivalent to the original packaging. ALL EXPRESS AND

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS OF PURPOSE FOR

THE PRODUCT ARE LIMITED IN DURATION TO THE ABOVE FIVE-YEAR PERIODS.

UNDER NO CIRCUMSTANCES (WHETHER BASED IN CONTRACT OR TORT) SHALL

BOCA RESEARCH BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT,

SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS

OF BUSINESS, OR OTHER FINANCIAL LOSS AS A RESULT OF THE SALE,

INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR DISRUPTION

OF ITS PRODUCTS.

Boca Research reserves the right to make periodic changes or enhancements to any Boca

Research product without prior notification, but has no obligation to modify or update

products once sold.

This warranty gives you specific legal rights, and you have other rights which may vary

from state to state. This warranty is valid only in the United States.

Содержание M144Ai









































Отзывы: