background image

Installation Manual

HPNFC-RT

BocaFlasher.com

1 of 7

REV 04-2019

IP60

Dry Listing

Damp Listing

IP65

IP68

Wet Listing

INTRODUCTION:

The Boca HPNFC-RT is a line voltage fixture that eliminates the need for secondary transformers, making installation contractor 

friendly. The housing is a clear anodized aluminum with a durable finish making it weather and abrasion resistant. It is UL Listed 

 

for dry, damp or wet location (model dependent). See layout drawings for model provided.

1.  Input Voltage: 90-120VAC, 230-277VAC

2.  Total linear ft per 20A breaker: HO8 = 175’ 

 

Total linear ft per 20A breaker: HO6 = 200’ 

 

Total linear ft per 15A breaker: HO8 = 130’ 

 

Total linear ft per 15A breaker: HO6 = 150’

3.  Input Current: HO8 = 114mA RMS per linear ft. 

 

Input Current: HO6 = 95mA RMS per linear ft.

ELECTRICAL SPECIFICATIONS:

Fixtures must be installed by a qualified and licensed electrician 

in accordance with all national, state and local electrical codes 

and regulations. If any part of this manual does not meet the 

necessary codes and regulations, contact the factory for more 

information before attempting to install.

WARNING: DO NOT LIFT FIXTURE BY CABLES. Do not attempt to install or use the HPNFC-RT fixture without 

reading the installation instructions and safety labels completely.

This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/or 

putting undue pressure on the cable connections will not be covered under the warranty!

FAILURE TO ADHERE TO THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE. 

DO NOT MODIFY, ALTER OR ATTEMPT TO SERVICE THE HPNFC-RT DOING SO WILL VOID THE WARRANTY.

Max Temp: 55°C

Min. Temp: -40°C

Storage:

  Store in a dry, well-ventilated area when product is not in 

use. Keep the electrical cord away from heated surfaces 

when in use or not in use. If cord shows signs of damage

 

do not use, return product to manufacturer.

Cleaning: 

  Dry and Damp (IP65) Rated Fixtures: 

 

To clean surface use a soft damp cloth.

  Wet (IP68) Rated Fixtures: 

 

To clean surface use a soft cloth with mild soap and water.

MAINTENANCE:

Содержание HPNFC-RT








Отзывы: