Boca Flasher HPNFC-RT Скачать руководство пользователя страница 7

BocaFlasher.com

7 of 7

Installation Manual

HPNFC-RT

REV 04-2019

7. CONNECT TO A DIMMING SYSTEM

8. REMOVING FIXTURES FROM CLIPS

 (IF NECESSARY)

8a

 Slide a flathead screwdriver in 

between the clip and fixture.

8b

 While holding the fixture with your 

other hand, pull back on screwdriver 

to release from notch.

8c

 Once released from one notch, 

fixture can be fully removed.

1. DANGER:

To reduce the risk electric shock, always unplug the HPNFC-RT from electrical outlet before cleaning.

 

Cut breaker if outlet is not available.

2. To reduce the risk of burns, fire, electric shock or injury to persons:

 

Use the HPNFC-RT only for its intended use as described in these instructions.

 

Do not use attachments not recommended by Boca Flasher.

 

Never operate the HPNFC-RT if it has a damaged cord, cable or plug, if it is not working properly, if it has been dropped or 

damaged, or dropped into water. If the seal appears to be damaged/broken/torn return the fixture to a service center for 

examination or repair.

 

Keep cables away from heated surfaces

 

Never drop or insert any object into any opening.

 

Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

3. WARNING:

 

Do not attempt to install or use the HPNFC-RT without reading the installation instructions and safety labels.

 

Failure to adhere to these instructions could result in serious injury or property damage.

4. Do not modify, alter or attempt to service the HPNFC-RT:

 

Doing so will void the warranty.

5. There are no serviceable parts within the HPNFC-RT:

 

Please contact your local representative if issues arise on site during or after installation.

6. Do not use sharp tools near or on the fixture lens:

 

Doing so will result in property damage and void the warranty.

Boca Flasher, Inc. 508 South Military Trail, Deerfield Beach, Florida 33442 USA Phone: 561.989.5338 Fax: 561.982.8323 © 2017 Boca Flasher, Inc

We are constantly improving our fixtures and reserve the right to change options and specifications. Additional information & details at 

www.bocaflasher.com

. For 

specific requirements, contact your Boca Flasher sales representative. All rights reserved. All names and trademarks are property of their respective owners.

Содержание HPNFC-RT








Отзывы: