BNC PCO-6131 Скачать руководство пользователя страница 21

Berkeley Nucleonics Corporation    

 

2955 Kerner Blvd., San Rafael, CA 94901 °  Tel (415) 453 9955   °   Fax (415) 453 9956   °   www.berkeleynucleonics.com 

 

8.0  Warranty 

Berkeley Nucleonics Corporation. (BNC) warrants equipment it manufactures to be 

free from defects in materials and factory workmanship under conditions of normal 

use and agrees to repair or replace any standard product that fails to perform as 

specified within one year after date of shipment to the original owner. PCO-6131 and 

other OEM, a modified, and / or custom products are warranted, as stated above, for 

ninety (90) days from date of shipment to original owner. This Warranty shall not 

apply to any product that has been: 

I.  Repaired, worked on, or altered by persons unauthorized by BNC in such a 

manner as to injure, in BNC’s sole judgment, the performance, stability, or 

reliability of the product. 

II.  Subjected the product to misuse, neglect, or accident; or 

III.  Connected, installed, adjusted, or used otherwise than in accordance with 

instructions furnished by BNC. 

 

BNC reserves the right to make any changes in the design or construction of its 

products at any time, without incurring any obligation to make any change whatever 

in units previously delivered. 

 

BNC’s sole obligation, and buyer’s sole remedies, under this agreement shall be 

limited to a refund of the purchase price, or at BNC’s sole discretion, to the repair or 

replacement of products in kind that prove, to BNC’s satisfaction, to be defective, 

when returned to the BNC factory, transportation prepaid by the buyer, within the 

warranty period. BNC shall in no way be liable for damages consequential or 

incidental to defects in its products, for failure of delivery in whole or in part, for 

injuries resulting from its use, or for any other cause. 

 

Returns must be preauthorized and accompanied by a BNC return RMA  number. 

Return Material Authorization can be initiated from Berkeley Nucleonics Website at 

https://www.berkeleynucleonics.com/rma-form

 

 

 

The foregoing states the entire warranty extended by BNC and is given and 

accepted in lieu of 1) any and all other warranties, expressed or implied, including 

but not limited to the implied warranties of merchantability and fitness for any 

particular purpose and 2) any obligation, liability, right, claim or remedy in contract or 

tort.   

 

Содержание PCO-6131






















Отзывы: