BMW E46 Convertible 2000 Скачать руководство пользователя | Manualshive

Страница: 36 / 48

background image

The supply and drain lines from the hydraulic
unit to the solenoid block on the top frame are
connected through quick disconnect couplings
located on the left side of the top storage com-
partment. Care should be taken when discon-
necting the lines not to drip the hydraulic fluid
onto the top fabric.

Ensure that all wiring is disconnected from the top frame before removing the top assem-
bly. There are three connectors on each side of the top assembly in front of the top stor-
age compartment. The main wiring harness (18 Pin ELO) from the CVM to the top frame
must also be disconnected.

THE TOP FRAME IS UNBOLTED FROM THE FRAME MOUNTING BRACKETS, MOUNT-
ED IN THE STORAGE COMPARTMENT. THESE BRACKETS ARE PRE-SET AND
ADJUSTED FOR TOP ALIGNMENT AT THE FACTORY AND MUST NOT BE REMOVED OR
ADJUSTED WHEN CARRYING OUT SERVICE WORK ON THE TOP.

F

Frra

am

me

e B

Brra

ac

ck

ke

ett

Set at Factory

ART-HYDLINES

ART-TOPFRAMECON

«
...
34
35
36
37
38
...
»

Содержание E46 Convertible 2000

















































Отзывы:

Нет отзывов

Похожие инструкции для E46 Convertible 2000

ESCALADE - BROCHURE 2009

Бренд: Cadillac Страницы: 24

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 20

Бренд: RAM Страницы: 292

Бренд: RAM Страницы: 116

Бренд: Whispbar Страницы: 15

Бренд: Mercedes-Benz Страницы: 358

Бренд: Thule Страницы: 8

2000 Oldsmobile Intrigue

Бренд: Oldsmobile Страницы: 348

Бренд: v.LOGiC Страницы: 22

Бренд: Linear Logic Страницы: 8

Бренд: v.link Страницы: 19

Easy Air Auto Screen

Бренд: Wagan Страницы: 8

Crossland X 2017

Бренд: Vauxhall Страницы: 245

Бренд: Acura Страницы: 19

Бренд: Ford Страницы: 325

Бренд: Oldsmobile Страницы: 276

Бренд: Volkswagen Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды