BMW E46 Convertible 2000 Скачать руководство пользователя | Manualshive

Страница: 33 / 48

background image

33

E46iCCVM/ST039/3/21/00

Hard Top

An accessory hard top is available for the E46iC. It is constructed from aluminum with a
finished fabric upholstery on the inside. Roof rack mounting points are integrated into the
top on the left and right sides.

The hard top attaches to the vehicle at four places:

• Two hard top locks on the left and right sides in the rear.
• Two cowl locks at the front.

ART-HARDTOP

ART-HLOCK1

ART-HRT-HLOCK2

«
...
31
32
33
34
35
...
»

Содержание E46 Convertible 2000

















































Отзывы:

Нет отзывов

Похожие инструкции для E46 Convertible 2000

Бренд: Mazda Страницы: 527

2008 Escalade EXT

Бренд: Cadillac Страницы: 496

Бренд: Kia Страницы: 54

Бренд: Metra Electronics Страницы: 2

Бренд: Farad Страницы: 8

Бренд: PEUGEOT Страницы: 128

Бренд: Schumacher Electric Страницы: 87

2009 ESCALADE ESV

Бренд: Cadillac Страницы: 602

Бренд: Volvo Страницы: 188

Бренд: Actia Страницы: 102

Бренд: Menabo Страницы: 12

Бренд: Audiovox Страницы: 24

Бренд: Mercedes-Benz Страницы: 2

Бренд: Westin Страницы: 2

Бренд: Tachosys Страницы: 28

Бренд: Volvo Страницы: 266

Бренд: Reese Explore Страницы: 9

Бренд: Honda Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды