BMS 74575 страница 26 Скачать руководство пользователя

Страница: 26 / 28

．

Trouble Shooting BMS INVERTED BIOLOGICAL

Under certain condition, some no-fault factors will bring a reversible influence to the instrument’s

performance. If the problem is happened, please take

proper measures according to the follow table. If

you can’t solve the trouble by the supplied methods, please contact with the sales department of our

company.

PROBLEM REASON

SOLUTION

PAGE

I、Optical Part:

The plug of the lamp holder is
not connected into the
illumination set

Connect them well

The bulb burnt out

Change a new lamp

The brightness is too low

Adjust to a proper position

The color filter is piled too
much

Minimize the number of the
filters

1. The illumination
is opening, but the
field of view is dark.

No use the appointed lamp
bulb

use the specified halogen Lamp
6V30W

The nosepiece is not in the
located position

Turn the nosepiece into the
position where you can hear
“clicked”

the color filter is stopped
midway

Insert deeply

2. The edge of the
field of view has
shadow or the
brightness is
asymmetry

The phase contrast slider is not
located in the proper position

Turn the slider into the
“clicked” position

There are stains on the

specimen

Change a clean specimen

Find dust and

stain in the field
of view

There are stains and dust

on the eyepiece

Clean the eyepiece

4. appear double
image

the size of the aperture
diaphragm is too small

Open up the aperture
diaphragm

The nosepiece is not in the
center of the light path

ensure the nosepiece is turned
into the “clicked” position

the aperture diaphragm in the
view of field is opened too
large or too small

adjust the aperture diaphragm
correctly

The lens (condenser, objective,
ocular or culture dish)
become dirty

Clean all

In the phase contrast
observation, the bottom
thickness of the culture dish is
more than 1.2mm.

Use a the culture dish whose
bottom thickness is less than
1.2mm

5. Resolution
problems

：

Image is not
sharp

；

The contrast is
not high

；

The detail is
not clear

；

Don’t obtain
the phase
contrast effect

Use a bright field objective

Change to the phase contrast
objective

Содержание 74575





























Результаты поиска

Содержание 74575

Отзывы:

Похожие инструкции для 74575

Бренды по названию

Популярные бренды

BMS 74575, Руководство пользователя

Результаты поиска

Содержание 74575

Отзывы:

Похожие инструкции для 74575

Бренды по названию

Популярные бренды