background image

Use Notices                                                  BMS INVERTED BIOLOGICAL 

 

I

Safety Note 

 

 

 

 

 

 

 

 

 

 

 

Ⅱ、

Maintenance 

1

 

Use the gauze to wipe the glass parts gently .If    removing the fingerprints and oil stains , slightly 
dampen gauze with the xylene or the admixture liquid which comparison is 3:7 of the ethanol and 
the aether to wipe. 

★ 

Note: the ethanol and the aether are all very combustible, do not put these chemicals near fire 

or the possible electricity spark source such as the electronics equipments open ,close 

operation . Use these chemicals in a well ventilated room as far as possible. 

2

 

Don’t use organic solvent to wipe the non-optical elements, If you need to clean, use the neutral 
detergent, please. 

3

 

When using, if the microscope is splashed by liquid, cut off the power at once, and wipe up the 
moisture. 

4

 

Do not disassemble any parts of the microscope. That will affect the function or decline the 
performance of the microscope. 

5

 

If haven’t mounted the objective , please cover the dust cap to prevent the dust and the splashed 
liquid of the tissue culture entering the inside. 

6

 

When not using, remember to cover up the microscope with the dust casing. And make sure the 

1

 

Do not keep the instrument in a direct sunlight, 

high temperature or humidity, dusty and easy 

shaking environment. Make sure the stage is plane, 

horizontal and stable enough. 

2

 

When moving the microscope, please hold up the 
instrument with one hand on the lower side of the 
eyepiece tube

, and the other hand on the 

illumination bracket

.

figure1

 

3

 

If the bacterium solution or the water splash to the 
stage, objective or viewing tube, pull out the power 
cord at once, and wipe up the microscope. 
Otherwise, the instrument will be damaged. 

4

 

When working, the lamp house on the top of the 
arm

(figure1) will become very hot, be sure there 

have enough room around the lamp house 
(especially the top) for cool. 

5

 

Before replacing the lamp bulb or fuse, turn the 
main switch on the “O”(off) position, then cut off 
the power. If the lamp is on, or soon after it has 
been turned off, it is hot and will cause serious 
burns, please do the replacement after it cool down 
completely. 

★ Specified: the halogen lamp 6V/30W 

6

 

Earth this instrument to prevent the lightning strike. 

7

 

Use the supplied power cord, please. 

Figure 2 

Figure 1 

4

Содержание 74575





























Отзывы: