BMB
4/10
e-mo-desk, two engines, 600-1250mm / 700-1200mm
Art.-No. 4884.617, 4884.618, 4884.666, 4884.688,
4884.717, 4884.718, 4884.766, 4884.788
l
2
3
4
5
ASSEMBLY
•
1 a
C
2
-
2
-1
>
\
-
\
a
a
I
•
10
�
�
o/
I
'
•
•
•
•
0
0
0
Lay out all components and hardware to ensure that you have all the components and hardware listed on the parts page.
Slide the Control Box (part 6) off the Frame End-CB (part 3a) and set aside. Fully separate Frame !End (part 36) from
Frame End-CB (part 3a). You will find the Center Rails (part 4) inside.
Place one of the Legs (part
l)
into the Frame End-CB (part 3a) ensuring that the
bar (arrow) is on "top" in relation to the Leg (part
l ).
Line up the holes on the Leg (pa
,
rt
l)
with the holes on the Frame End-CB
(part 3a).
Using the supplied Allen Wrench, insert four (4) M6x
l
0 Machine Screws
(part 10) through the holes in the Frame End-CB (part 3a), going into the Leg
(part
l)
and rotate each screw just a few turns. After all four (4) M6x
l
0
Machine Screws (part
l
0) are inserted, tighten all four (4) screws.
Do the same for the other Leg (part 1) and the Frame End (part 36).
0
if you drop a screw inside the frame end, simply tilt to retrieve.
0
The 'Frame End-CB (part 3a) should be placed on the side of the desk where
you plan to mount the Control Box (part 6) and the Handset (part 7).
Slide the Side Bracket (part 5) into the Frame End-CB (part 3a). Insert two (2)
M6x 14 Machine Screws (part
l l)
through the two (2) holes in the bottom of
the frame end/leg assembly and into the tabs in the Side Bracket (part 5).
Using the supplied Allen Wrench, rotate each screw just a few turns. After
both M6x 14 Machine Screws are inserted, tighten both screws.
Do the same for the other fro me end/leg assembly.
Slide the two (2) Center Rails (part 4) into the two Frame Ends (parts 3a
&
36) ensuring:
a) the slots in the Center Rails (part 4) face inward
b) the slots in the Center Rails (part 4) are closer to the top edge when the assembly is upside down (see inset).
111
For each leg assembly, attach a Foot (part
2)
with four (4) M6x 14 Machine
Screws (part
l
1 ) and tighten in a cross-pattern.
page 4
1. Lay out all components and hardware to ensure that you have all the components and hardware
listed on the parts page. Slide the Control Box off the Frame End-CB and set aside. Fully
separate Frame End from Frame End-CB . You will fi nd the Center Rails inside.
2. Place one of the Legs into the Frame End-CB ensuring that the
bar (arrow) is on "top" in relation to the Leg . Line up the holes on the
Leg with the holes on the Frame End-CB . Using the supplied Allen
Wrench, insert four M6x14 Machine Screws through the holes
in the Frame End-CB , going into the Leg and rotate each screw
just a few turns. After all four M6x 14 Machine Screws are
inserted, tighten all four screws.
Do the same for the other Leg and the Frame End .
3. The Frame End-CB should be placed on the side of the desk where
you plan to mount the Control Box and the Handset .
Slide the Side Bracket into the Frame End-CB . Insert two M6x14
Machine Screws through the two holes in the bottom of the frame
end/leg assembly and into the tabs in the Side Bracket . Using the
supplied Allen Wrench, rotate each screw just a few turns.
After both M6x14 Machine Screws are inserted, tighten both
screws.
Do the same for the other frame end/leg assembly.
4. Slide the two Center Rails into the two
Frame Ends and ensuring:
a) the slots in the Center Rails face inward
b) the slots in the Center Rails are closer
to the top edge when the assembly is
upside down (see inset).
5. For each leg assembly, attach a Foot with four M6x14
Machine Screws and tighten in a cross-pattern.
ASSEMBLY
