The BlueSpot Air Hammer and Chisel Set is ideal for general body shop work and rust removal.
The set comes complete with 4 chisels: Spot weld breaker, body panel cutter, taper punch and
ripping chisel.
Please make sure that you read these instructions carefully in order to avoid injury when using
the air hammer and chisel set. Follow all health and safety rules and regulations. If in doubt and
available please contact a more knowledgeable source.
DO NOT use if damaged.
•
ALWAYS
check the air hammer, air hose and chisels for damage before use. If damaged
do not use.
•
ALWAYS
check the chisels before use. Do not use blunt chisels as these can cause
damage to the workpiece or cause injury.
•
ALWAYS
check the work area before starting. Make sure there are no hidden electrical
wires, gas pipes etc. This could be very dangerous.
• Maintain tool in good and clean condition for best and safest performance.
• Keep the work area clean, uncluttered and ensure there is adequate lighting.
• Maintain correct balance and footing. Ensure the floor is not slippery and wear
non-slip shoes.
• Keep children and unauthorised persons away from the work area.
• For best and safest performance always ensure the tool is cleaned and maintained
regularly. The tool should always be cleaned before being stored away.
•
ALWAYS
dress appropriately – clothing should be close fitted and long hair tied back.
Jewellery should be removed and shoes should be worn with a non-slip sole.
•
ALWAYS
wear the correct eye or face protection when operating the air hammer.
•
ALWAYS
wear approved respiratory protection. This will help protect you from
any dust.
•
ALWAYS
wear ear protectors when using the air hammer.
•
ALWAYS
ensure you work in a well ventilated room.
•
NEVER
use oxygen, CO
2
, combustible gases or any bottled gas as a source of power.
•
ALWAYS
ensure the tool is used with a correctly rated compressed air supply.
•
ALWAYS
ensure the air hammer trigger is not pressed when connecting to the air hose.
•
ALWAYS
make sure that the air supply hose is kept away from heat, oil and sharp edges.
•
DO NOT
exceed the maximum pressure for the tool of 90 psi / 6.2 bar.
•
DO NOT
operate the air hammer if you are tired as this could be dangerous.
•
DO NOT
get the air hammer wet. Always use in dry locations/conditions.
02
Introduction
Specification
Maximum Operating Pressure
Working Air Pressure
Air Consumption
Maximum Blows Per Minute
Air Inlet Size
Vibration Levels
Sound Pressure Level
Sound Power Level
Dimensions
Weight
100 PSI
90 PSI
4.5 CFM
4500 blows per minute
¼” BSP
12.04 m/s2 (Uncertainty K is 1.06 m/s2)
99.3 dB
110.3 dB
14.5 x 16 x 5cm
1.4 kg
Safe use (continued)
•
NEVER
try to get the air hammer to perform a task that it was not made for. Do not
overload or misuse the tool.
•
ALWAYS
disconnect the air hammer from the air supply when it is no longer in use or
is being passed to another person.
•
ALWAYS
check and adhere to national regulations when disposing of the air hammer.
•
BE AWARE
that the tool vibrates when in use. Vibration may be harmful to your hands
or arms. Stop using the tool immediately if the tool causes discomfort or pain occurs.
Seek medical advice.
•
NEVER
carry an air tool by the air supply hose or with your finger on the trigger.
•
NEVER
use accessories that are not designed for use with the air hammer.
•
NEVER
use any of the chisels supplied as a hand tool. They must only be used with the
air hammer.
•
NEVER
leave the air hammer unattended. When you have finished using the air
hammer it should be disconnected from the air supply and stored away in a safe place
that is out of reach of children.
•
NEVER
operate the tool if you are under the influence of drugs or alcohol as this can
be dangerous.
