Bluerock Tools 12

M W S -                         1 2 ” Z 1 L R B / T S   C O R E   D R I L L  

 

 

UNPACKING THE ITEM 

CAUTION: This machine is packed together with items that may be sharp, oily and overly 
heavy objects.  Remove the machine from the packaging in a safe manner.  Check to ensure 
all accessories are included with the item while unpacking.  If any parts are found to be 
missing, contact the retailer as soon as possible.  Do not throw away the packaging until the 
item is out of the guarantee period.  Dispose of the packaging in an environmentally 
responsible manner.  Recycle if possible.  Keep all plastic bags away from children due to risk 
of suffocation.       

 

  

WEEE - Waste Electrical & Electronic Equipment. Note this machine should be disposed of as electrical & electronic waste. 

 

 

 

SLURRY DISPOSAL 

NOTE: It is recommended to dispose of the drilling slurry (the muddy/dusty water material) in 
an environmentally responsible manner.   The disposal of slurry directly into sewage 
systems, sewers, lakes, rivers, or direct earth without treatment can be environmentally 
harmful and possibly illegal.  Ask your local public authorities about current regulations in 
your area.   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ã

 THE NEWMAN TRADING COMPANY LLC DBA BLUEROCK® TOOLS 2020 

1033 ANDOVER PARK EAST, TUKWILA WA 98188 USA 

Phone 206.604.8363 • Fax 425.572.5167 

www.bluerocktools.com 

 

Содержание 12"Z1/LRB/TS





















Отзывы: