background image

 
 

 

 

 

Blue Whale Spa Ltd, 11 Glaisdale Drive East 

 Nottingham, NG8 4GU

 

-2- 

 

 

MVP260 Control Reference Card 

Non-Circ Operation 

 
Initial Start-up 

 

When your spa is first actuated, it will go into Priming mode, indicated by  “   

 

” Please see the M-7 Installation Instruction 

Manual for complete instructions on Power-up and Pump Priming. The Priming mode will last for less than 5 minutes 
(press "Temp" or "Set" to skip Priming Mode) and then the spa will begin to heat the spa and maintain the water temperature in the 
Standard mode. 

 
 

 
 
 

Temp/Set (80°F - 104°F / 26°C - 
40°C) 

The  start-up  temperature  is  set  at  100F°/37°C.  The  last 
measured temperature is constantly displayed on the LCD. 
Note  that  the  last  measured  spa  temperature  displayed  is 
current only when the pump has been running for at least 2 
minutes. 
To display the set temperature, press the “Temp” or “Set” pad 
once. 
To  change  the  set  temperature,  press  the  pad  a  second 
time before the LCD stops flashing. Each press of the “Temp” 
or  “Set”  pad  will  continue  to  either  raise  or  lower  the  set 
temperature. 
If the opposite direction is desired, release the pad and let 
the  display  revert  to  the  current  water  temperature.  Press

 

the pad to display the set temperature, and again to make 
the temperature change in the desired direction. 
After three seconds, the LCD will stop flashing and display the 
current spa temperature. 
Note:  If  there  is  not  a  blower  on  the  system,  an  alternate 
panel with separate "Up" and "Down" buttons in place of a 
"Set" or "Temp" button may be used. Simply press "Up" or 
"Down" where a "Temp" or "Set" button press is indicated.  
(Ignore the "direction reversal paragraph.") 

Jets 

Touch  the  “Jets”  button  once  to  activate  the  low  speed  of 
the  pump  and  again  for  the  high  speed.  Press  the  “Jets” 
button  again  to  turn  off  the  pump.    If  left  running,  the  low 
speed of the pump will automatically turn off after 4 hours, 
and  the  high  speed  will  automatically  turn  off  after  15 
minutes. The low speed of the pump runs when the blower 
is  on.  It  may  also  activate  for  at  least  2  minutes  every  30

 

   

   

Содержание Balboa MVP260








Отзывы: