Blue Seal SMW 15, Инструкция по эксплуатации и техническому обслуживанию

Страница: 12 / 19

12
SMW 15
correct level has been reached, the water will
automatically begin to heat. This is indicated by a
flashing light (3). Wait until the preset temperature has
been reached and the light (3) becomes fixed.
The machine will be ready to start the washing cycle
when the temperature in the tank (indicated by
thermometer 7 Fig. 1 on the panel ) reaches at least
50
°
C.
5. Open the door and pour the quantity of detergent
indicated by the manufacturer directly into the tub. This
operation need not be carried out when the machine is
equipped with the optional dispenser.
6. Choose the cycle length by means of the selector (4).
3.3.b Washing operations (Fig 8)
1. Load the dirty crockery into the basket (as indicated in
Fig. 10).
2. Press the START button (5), and the washing and
rinsing cycle will automatically begin and the warning
light (6) will come on.
3. The light (6) will go out to indicate that the cycle has
terminated. Now open the door and remove the basket.
4. Add a half of coffee cup of detergent after every 5/6
washes. This operation need not be carried out if the
machine is equipped with the optional dispenser.
The doses are indicative and not binding since they
vary according to the hardness of the water and utilized
type of detergent.
3.3.c Changing the water (Fig. 9)
This operation must be carried out after every 10 cycles or
so, according to the amount of accumulated dirt.
1. Remove the tub filters (22).
2. Switch off the machine as indicated in paragraph 3.3.d,
then lift the overflow (23) and allow the tub to completely
drain.
3. Refit the overflow (23) and the filters (22) in its housing
and repeat the machine preparation operations as
indicated in paragraph 3.3.a.
3.3.d Switch-off (Fig. 9)
At the end of the work day, set the line switch (1) to position
“0” OFF, discomnnect the main switch installed prior to the
machine and turn off the water delivery cock.
ATTENTION
Disconnect the main circuit-breaker prior to the machine
and turn off the water delivery cocks if the dishwasher is
faulty or operates badly.
Only allow the manufacturer’s authorized after-sales
service center to make repairs.
3.3.e Manual drain timering (Fig. 1)
(on machine with drain pump only)
To manually empty the water from the tub, switch off the
line button (6) Fig. 1 and push the START/DRAIN button
(1) for a determinated time.
Repeat the doove mentioned operations till when the tank
is completely empty.
3.3.f Alarms (Fig. 8)
The machine will set to the alarm status in the following
cases:
•
Tub refilling timeout.
If tank filling fails to terminate within 20 minutes, the
machine will set to the alarm status. This is indicated by
fast flashing warning light (6). Switch off the machine
by turning selector (1) to 0 “OFF” to reset the alarm.
• No water in the tub.
When the safety level probe detects insufficient water,
the function in progress will abort, the tub and boiler
heating function will be inhibited and the machine will
set to the alarm status. This is indicated by fast flashing
warning light (6). Switch off the machine by turning
selector (1) to 0 “OFF” to reset the alarm.
• Overheating.
If the temperature of the water in the boiler or tub
exceeds 98
°
C, the machine will set to the alarm status,
inhibiting all functions and any cycle in progress. The
alarm status is indicated by fast flashing warning light
(3).
The alarm automatically disactivates when the tempe-
rature drops below 90
°
C. Failing this, switch off the
machine by turning selector (1) to 0 “OFF” to reset.
• Heating timeout.
The machine will set to the alarm status if, after 20
minutes continuous boiler heating, the temperature
remains less than 45
°
C. This is indicated by fast
flashing warning light (3).
Switch off the machine by turning selector (1) to 0
“OFF” to reset.
ATTENTION
Contact the after-sales service center if the alarm
continuously activates.
ENGLISH