manualshive.com logo in svg

Blonder tongue HDE-4S-PRO, Руководство пользователя

Поделиться
Скачать
Blonder tongue HDE-4S-PRO Скачать руководство пользователя страница 8

8 HDE-4S-PRO 

Instruction Manual

INPUT POWER: 

IEC 14 power inlet plug - rated 115/230 VAC; 2.0/1.0A; 60/50 Hz; equipped with Slo-Blo, 3.0 Amps, 250 V Fuse. 48 

VDC power (optional) is provided on stk# 6372 48.

EAS CONTROL:

Terminal strip to activate the EAS messaging feature in one of two following ways:

a)  5-12 VDC between terminals 1 & 3 shown below

b)  Dry Contact between terminals 2 & 3 shown below

 

                                    1    2    3

                                        GND
NOTE:

 This feature is intended to activate EAS and override all input programs 

with the EAS INPUT (see        below for details). The QAM RF OUT (see        below), ASI OUT (see  3   ) and DATA OUT       

(see       ) will all contain the EAS content on every program.

 

EAS INPUT: 

RCA connectors for EAS Analog Audio (marked L & R) and Composite Video (marked VIDEO) inputs. 

HD-SDI 1 - 4: +Spare input

BNC connectors to receive the HD-SDI inputs with loop-thru outputs for monitoring.

CC IN 1, 2, 3 & 4:

RCA connectors (marked “CC IN”) for Analog NTSC Closed Captioning (EIA-608, also known as Line 21), which will 

then be digitized and inserted in the MPEG-2 Transport Stream of the Component inputs.

  DATA OUT 1 GIGE:

RJ45 connector for GigE (1000Base-T Ethernet) interface for multiplexed SPTS or MPTS output streams. Only static IP 

address can be assigned to this interface. The factory default value is 192.168.253.1. 

  REMOTE CONTROL 10/100:

RJ45 connector for 10/100Base-T Ethernet interface for monitoring and configuring the unit. Only static IP address can 

be assigned to this interface. The factory default value is 172.16.70.1.

QAM RF OUTPUT: 

“F” connector for up to four (4) QAM RF outputs. 

   IP RESET:

When pushed and held for about 10 seconds, resets the IP address, Usernames, and Passwords to Factory default 

values as follows:

IP address = 172.16.70.1

Username = Admin (case-sensitive)

Password = pass (case-sensitive)

EAS FEATURE IS FUNCTIONAL ONLY WHEN (I) EAS CONTROL IS TRIGGERED ON, AND (II) VIDEO/AUDIO 

IS DETECTED ON EAS INPUT CONNECTORS. THE EAS FEATURE WILL NOT BE FUNCTIONAL UNLESS BOTH 

THESE CONDITIONS ARE MET.

5

6

7

9

8

7

12

3

10

12

11

10

13

9

5

6

7

13

12

8

10

11

-48 VDC Option 

Stk# 6372 48

Содержание HDE-4S-PRO









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды