background image

TS ID: user must enter the identification number for the output TS. The range is 1 to 65535. The TS 

ID assigned must be unique.

Bit rate Select: User selects from the 4 profiles set in the General TS Configuration section.

VCT: MPEG Virtual Channel Table selections are off, TVCT (terrestrial) and CVCT (cable)

Modulation Mode: user can select the modulation mode for the MPEG TS table.  Options are: 

Reserved, Analog, QAM64, QAM256, 8-VSB, and 16-VSB

Out of Band: an out-of-band (OOB) is a channel which is the combination of the forward and 

reverse  OOB  channels.  When  a  cable  virtual  channel  is  flagged  as  being  out-of-band,  it  is 

carried on the out-of-band channel. Possible options are Enable, and Disable. When Enabled, 

assigns the OOB bit in the TS packet and labels the TS as out-of-band.

STEP 6 - Main > TS Configuration

The setting parameters are basically the same between DEMUX and MUX modes with the exception 

of the number of Output TS’ and the “Re-PID” option (Disable/Enabled) on DEMUX mode.

General TS Configuration

There are (4) User TS Bitrate preset profiles.   The available selections are 38.81, 19.39, 12.00, 8.00 

Mbps or User Defined.  

TS Output Configuration

If Re-PID’ing (only in DEMUX MODE) is desired, select “Enabled” on the corresponding TS0.  Output 

PID and Programs number can then be changed.  The Default is “Disabled” with these fields grayed 

out.   On MUX Mode the PIDs can always be changed.

DEMUX & MUX MODES

A

1

2

3
4

5

1

2

6

3

7

8

9

4

5

Содержание FlexCoder









Отзывы: