BLOCKsignalling ASP1A Скачать руководство пользователя

Страница: 13 / 18

Page 13 of 18

BLOCKsignalling

www.blocksignalling.co.uk

Example Wiring to Eckon or Berko 4-aspect Signal

The positive connection from each of the leds in an Eckon or Berko signal match the
led colour (red wire for the red led positive connection, etc).

Depending on the age of the signal, there will be one or more white wires. These
are the negative connections to the leds.

The exception is the top yellow led of a 4-aspect signal. This has a blue positive
wire and may have a black negative wire (or it may share a white negative wire with
the rest of the leds).

The following wiring diagram shows the most common wiring arrangement.

BLUE WIRE (TOP YELLOW LED +)

GREEN WIRE (GREEN LED +)

YELLOW WIRE (LOWER YELLOW LED +)

RED WIRE (RED LED +)

BLACK WIRE (TOP YELLOW LED -)

RED

GREEN

YELLOW

BLOCK

signalling

WHITE WIRE (S) (LED -)

Detector

POWER

SUPPLY

Содержание ASP1A



















Результаты поиска

Содержание ASP1A

Отзывы:

Похожие инструкции для ASP1A

Бренды по названию

Популярные бренды

BLOCKsignalling ASP1A, Руководство пользователя

Результаты поиска

Содержание ASP1A

Отзывы:

Похожие инструкции для ASP1A

Бренды по названию

Популярные бренды