BLOCKsignalling ASP1A Скачать руководство пользователя | Manualshive

Страница: 4 / 18

background image

Page 4 of 18

BLOCKsignalling

www.blocksignalling.co.uk

Factory Reset

To reset the module back to factory settings, switch off the power to the module and
hold down the Push Button. Apply the power and continue holding the push button
until

1 flash

of the led is seen. At this point, release the button. You will see a long

flash of five seconds.

The led will begin flashing again. When you have seen

1 flash

press the button. You

will see a long flash of five seconds and then 10 rapid flashes. The reset procedure
is then complete and the module will restart with factory settings, and run the 4-
aspect signal mode. If you make a mistake programming, simply repeat the process.

Led Connection

When using leds it is important to connect them the right way around.

The negative lead (cathode) is identified by a flat on the side of the led body, and by
having a shorter lead.

«
...
2
3
4
5
6
...
»

Содержание ASP1A



















Отзывы:

Нет отзывов

Похожие инструкции для ASP1A

Бренд: Valve Concepts Страницы: 15

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 78

Бренд: Panasonic Страницы: 98

Бренд: NAiS Страницы: 173

Бренд: Panasonic Страницы: 2

Бренд: B&G Страницы: 2

Бренд: B&K Страницы: 9

Бренд: Baby Jogger Страницы: 16

Бренд: GAUGEMASTER Страницы: 2

Бренд: EasyIO Страницы: 19

Бренд: Zero 88 Страницы: 2

Бренд: Zenit Страницы: 24

Бренд: PAC Страницы: 17

Бренд: Rabbit Страницы: 38

Бренд: R82 Страницы: 8

Бренд: Samson Страницы: 56

Бренд: EasyIO Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды