Blizzard POWER PLOW 810-1 Скачать руководство пользователя | Manualshive

Страница: 4 / 52

background image

Lit. No. 68251, Rev. 09

4

May 1, 2021

SAFETY DEFINITIONS

NOTE: Indicates a situation or action that can lead
to damage to your snowplow and vehicle or other
property. Other useful information can also be
described.

WARNING/CAUTION AND INSTRUCTION
LABELS

Become familiar with and inform users about the
warning and instruction labels on the back of the
blade.

NOTE: If labels are missing or cannot be read, see
your sales outlet.

SAFETY

WARNING

Indicates a potentially hazardous situation
that, if not avoided, could result in death or
serious personal injury.

CAUTION

Indicates a potentially hazardous situation
that, if not avoided, may result in minor or
moderate injury. It may also be used to alert
against unsafe practices.

• Kickstand must be lowered, with kickstand pin seated in lower hole on pivot beam.
• Slowly drive vehicle forward until pushbeam receiver mount points contact

A-frame mount bushings.

• Turn POWER HITCH OPERATION switch (on plow control) to "ON" position.
• Connect plow and vehicle electrical harnesses. Connect weather caps together.

•  Raise plow. Lower kickstand until kickstand pin is seated in lower hole on pivot beam.
•  Lower plow on flat, level surface. Turn vehicle ignition off.
•  Remove hitch pins from A-frame and undercarriage.
•  Turn vehicle ignition on.
•  Turn POWER HITCH OPERATION switch (on plow control) to "ON" position.

• Pull A-frame latch lock pin out and lower A-frame latch over draw pin.
• Push and hold CONNECT/DISCONNECT switch upward. POWER HITCH arm

will engage back of pushbeam and pull plow into pushbeam receiver mount
points on vehicle.

• Insert both hitch pins and secure each with hair pin cotter.
• Lower POWER HITCH arm to relieve tension on A-frame latch. Raise A-frame

latch and lock into position with lock pin. Raise plow.

• Raise kickstand until kickstand pin seats into upper hole on pivot beam.

• Push and hold CONNECT/DISCONNECT switch downward. POWER HITCH

arm will disengage from behind undercarriage pushbeam and lower.

•  Disconnect plow and vehicle electrical harnesses. Install weather caps.
•  Turn SYSTEM POWER (on plow control) to "OFF" position.
•  Slowly move vehicle backward away from plow.

MOUNT INSTRUCTIONS

DISMOUNT INSTRUCTIONS

Read Owner's Manual for Complete Instructions.

Read Owner's Manual for Complete Instructions.

WARNING: Keep fingers away from plow and truck mounting points.

WARNING: Keep fingers away. POWER HITCH arm raises behind undercarriage pushbeam.

A-Frame
Latch

Hitch
Pin

A-Frame
Latch
Lock Pin

Draw
Pin

A-Frame Latch

rotates clockwise

and hooks onto

Draw Pin

CONNECT/DISCONNECT
POWER HITCH Switch

Adjustable
Kickstand

Adjustable
Kickstand

A-Frame
Mount Bushing

Pushbeam
Receiver
Mount Points

POWER
HITCH Arm

Slowly Move
Vehicle Forward

Slowly

Move Vehicle

Backward

Undercarriage
Pushbeam

CONNECT/DISCONNECT
POWER HITCH Switch

CONNECT/DISCONNECT
POWER HITCH Switch

POWER
HITCH Arm

POWER HITCH Arm

Hitch

Pin

Kickstand Pin

Kickstand Pin

Adjustable
Kickstand

Kickstand Pin

STEP #1

STEP #2

44812

U.S. Patents 5,638,618; 5,899,007; 6,178,669; 6,276,076; 6,393,737; 6,408,549; 6,412,199; 6,442,877; 6,615,513; Canadian and other patents pending.

POWER PLOW™ &

SPEEDWING™ Blades Only

(both sides)

«
...
2
3
4
5
6
...
»

Содержание POWER PLOW 810-1





















































Отзывы:

Нет отзывов

Похожие инструкции для POWER PLOW 810-1

Бренд: Lamson Страницы: 3

Бренд: GreenWorks Commercial Страницы: 41

HOPWINN HS100-1900A150P

Бренд: Hopewind Страницы: 26

FATMAX V20 LITHIUM ION SFMCBL730

Бренд: Stanley Страницы: 16

Бренд: Cub Cadet Страницы: 32

Craftsman 944.525410

Бренд: Sears Страницы: 48

Бренд: Worx Страницы: 10

Бренд: Giant-Vac Страницы: 16

Бренд: Badger Basket Страницы: 40

Бренд: Poulan Pro Страницы: 24

Бренд: FujiFilm Страницы: 68

Бренд: Herz Страницы: 20

Бренд: Snapper Страницы: 116

Бренд: GreenWorks Tools Страницы: 206

Бренд: Yard-Man Страницы: 16

WORLD 50 HZ K3EU180A50

Бренд: York Страницы: 8

PowerPlus POWXG4038

Бренд: VARO Страницы: 11

Бренд: Makita Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды