manualshive.com logo in svg

Blease 8500, Руководство по обучению

Поделиться
Скачать
Blease 8500 Скачать руководство пользователя страница 49

Blease Test Procedure 

 

 

Title:  B.A.V. POWER SUPPLY PCB 

DocumentNo:129TP076 

Sheet 5 of  5 

 

 

5.11   Mains Operation

 

Toggle the following three jig switches: 

ALARM SOUND to OFF 

⋅

 +24V RELAY to NORM 

⋅

 PCB SUPPLY to AC 

After toggling the jig PCB MODE switch to ON, verify all supplies are restored to their 
nominal ON LOAD values. The BATT VOLTS may be a little low as charging is initiated due 
to previous testing. 

Verify on the jig that the PCB SUPPLY lamp is similarly illuminated as the adjacent JIG 
SUPPLY lamp. 

Note - the supply voltage to the board under test as shown on the UNREG +25V meter is 
protected by thermistors. These may trip if the board is allowed to run at full load for 
any length of time, particularly when running from AC. 

 

To regain normal operation, turn OFF the jig external DC

 and

 mains supplies for a 

couple of minutes.

 

 

5.12   Unregulated Supply

 

Results for the following are affected by the mains supply voltage which should be at its 
nominal value of 240 Vac. 

Note the value from the jig UNREG +25V meter. 

Toggle the jig PEAK READ switch down and again note the value from the jig UNREG +25V 
meter.

 

 

Содержание 8500






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды