manualshive.com logo in svg

Blease 8500, Руководство по обучению

Поделиться
Скачать
Blease 8500 Скачать руководство пользователя страница 18

 

Title:  8500 Adjustment & Calibration 

Document No: 129AC000 

Sheet 6 of  12 

 

BLEASE QUALITY DOCUMENT 

BQD 083.V2 

25/5/94 

 
 

Adjust RV1 on the Interface board for 0V +/-10mV at PFZ test pin. 

Press Space Bar to save. 

Press Ctrl+U to save zeros. 

 

 

Leak Test and Absorber Switching   

Absorber switching 

 

 

The function of this will have been checked during compliance compensation and the    

 

 

 

     presence of an absorber will have been displayed

.  

 

 

Fresh gas leak test  

 

 

Connect spirometry tubing 10110089 from TJ92 to the fresh gas connections on the rear of the 
ventilator.  Each side of the circuit is checked by pressurising it to 80 mmHg and checking that 
the pressure is maintained. 

Patient Flow transducer leak test 

Connect spirometry tubing 10110089 from TJ92 to the patient connections on the rear of the 
ventilator.  Each side of the circuit is checked by pressurising it to 80 mmHg and checking that 
the pressure is maintained. 

Drive Flow Sensor Leak Test 

Note: to run the Blease Medical Test I/O Diagnostics connect the ventilator serial cable between 
the recorder output connector on the back panel of the 8500 & a PC. Run Hyper Terminal on the 
PC using the stored 8500 HT settings file. 

Press 

CTRL+E

 on the PC followed by the up cursor key. Page through the diagnostics using the 

TAB key & scroll through using the UP/DOWN cursor keys.  

Tee in to the drive gas outlet the pressure monitor and then block the flow sensor outlet.  
Select 

Blow off valve ref. pressure

. With the flow sensor outlet blocked the internal pressure 

will build up until the Blow off valve operates. 

Using an oscilloscope monitor the voltage at test point DF on the BAV Interface Board 
10110099 this voltage will remain stable whilst the monitored pressure is stable if there are no 
leaks. 

Once this test is complete restart the ventilator by pressing CTRL + E. 

 

Run the ventilator for 3 hours on default settings, but with BPM set to 30. 

 

Содержание 8500






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды