Blaze King KING KT1102 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 29

background image

Date Printed: February 15, 2008

23

Version 1.01

MODEL PRINCESS PT1003 (non catalytic)

ROOF OR WALL EXIT CLEARANCES ARE THE SAME
FOR WALL EXIT CLEARANCE ABOVE HORIZONTAL CONNECTOR 18"

A

B

C

D

E

F

Parallel & corner

12"

7"

22"

14.5"

11"

22.5"

Parallel reduced side

use side shields

7"

7"

17"

14.5"

n/a

n/a

Parallel & corner close

clearance, use side
shields & rear shields
or fan

7"

6"

16"

13.5"

6"

16.5"

Alcove

7"

6"

n/a

n/a

n/a

n/a

Alcove minimum size 47"wide, 76" high, 48" maximum depth
Alcove installation requires side shields & rear shield or fan

INSTALLATION USING METAL CHIMNEY

When a metal prefabricated chimney is used, the manufacturer's installation instructions must be
followed precisely. Maintain the proper clearance to combustibles as recommended by the
manufacturer. The chimney must be the required height above the roof or other obstructions, see
figure 1.

1) Position your stove in the desired location and use a plumb line to mark the spot directly above
your stove where the chimney will exit the room.
2) Check to see that the area where the chimney will penetrate the wall or ceiling is clear before
cutting. Maintain structural integrity of the wall or ceiling.
3) Mark the exact location for the floor protection. It must extend 16" in front and 6" on each side and
6" to the rear of the stove. If you are using a wall exit the floor protector must extend to the wall
below the pipe and 6" on either side. Mark the location for combustion air supply.
4)

Set the stove aside and install the chimney in accordance with the chimney manufacturers

instructions.
5) Install the combustion air supply if applicable.
6) Install the floor protection.
7) Position the stove in its final location and connect the chimney connector pipe (see Figure 2) and
the combustion air supply.

Note: the chimney connector pipe is installed with the crimped end down

toward the stove, and each joint must be secured with 3 sheet metal screws.
8) Contact the local authority for a final inspection.

Carefully read the operating instruction in the front section of this manual.

Thank you! Have a cozy safe winter.

«
...
21
22
23
24
25
...
»

Содержание KING KT1102






























Отзывы:

Нет отзывов

Похожие инструкции для KING KT1102

Бренд: Zibro Страницы: 16

Powersaver Dual Flexi

Бренд: Sangamo Страницы: 2

Бренд: RADtec Страницы: 15

Бренд: RainScapes Страницы: 2

Бренд: Redring Страницы: 4

Бренд: Stahl Страницы: 45

Бренд: Haverland Страницы: 71

Бренд: Galletti Страницы: 32

Бренд: Calorex Страницы: 28

Бренд: Galletti Страницы: 40

VITOCAL 300-G PRO Type BW 2150

Бренд: Viessmann Страницы: 124

Бренд: Easylife Страницы: 3

Бренд: Archgard Страницы: 53

Бренд: Pentair Страницы: 4

SEPARATED COMBUSTION GAS FIRED PROPELLER UNIT HEATER

Бренд: Mestek Страницы: 32

Бренд: Sovelor Страницы: 16

INTERGAS Altherma EJHA-AV3

Бренд: Daikin Страницы: 36

Бренд: Strend Pro Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды