Blaze King BOXER 24 Скачать руководство пользователя страница 27

Страница: 27 / 51

180-BX24.1 v1.00

May 27, 2020

Page 27

BX24.1

CATALYST MONITORING

CATALYTIC COMBUSTOR, CLEANING

Under certain conditions, ash particles may become attached to the face of the combustor. These may be

seen while the combustor is in the glowing stage, or when the fire is out. Any deposit on the visible face

of the combustor should be removed. Wait until the fire is out and the appliance is cold before performing

any cleaning. Brushing the combustor with a soft bristle paint brush will remove some deposits. Passing

a vacuum cleaner wand or brush near the face of the combustor will remove most deposits. (Hot ash in a

vacuum cleaner bag will burn, may melt the vacuum or cause a house fire. Exercise caution and never clean

the appliance when the appliance or ashes are hot.) Never scrape the combustor with any hard tool or brush.

Never run pipe cleaner through the individual cells of the combustor. This is not needed, and may do more

harm than good. Limit cleaning to the face of the combustor.

NOTE: Never remove a combustor without

approved combustor gasket in hand as original gasket will fall apart when removed from

appliance.

Remember to re-install the Flame Shield (the perforated plate) in same position it was found.

TIP: A hot fire will usually prove to be the best method of cleaning the combustor of deposits.

CATALYTIC COMBUSTOR, TESTING

Light the fire as per the lighting instructions (see “LIGHTING THE FIRE”). Then set the thermostat knob on a

MED setting. When the fire is well established (within one to three hours) turn the thermostat knob between

LOW

and

MED

. A properly operating combustor will remain active, and the combustor thermometer will

remain in the “active” zone until the wood load is mostly consumed. A “tired” or “dead” combustor will, with

the thermostat on

MED

or lower, go out completely, and the thermometer needle will fall into the “inactive”

zone. Repeat this procedure several times over several days (Remember that the combustor thermometer

has a built-in lag of 4-8 minutes.) If, after several test burns, the thermometer will not indicate an “active”

combustor, it may require cleaning or replacement. It is also possible that the thermometer, itself, may not

be reading accurately. Before condemning the combustor, read “THERMOMETER”. If, after cleaning has

been performed, your combustor is still not working you can Contact Blaze King for a replacement combustor.

Please read “REPLACEMENT PARTS” section in this owners’ manual.

It is important to periodically monitor the operation of the catalytic combustor to ensure that it is functioning

properly. A non-functioning combustor will result in a loss of heating efficiency, and an increase in creosote

and emissions. Following is a list of items that should be checked on a periodic basis:

• Combustors should be visually inspected at least three times during the heating season to determine if

physical degradation has occurred. Actual removal of the combustor is not recommended unless more

detailed inspection is warranted because of decreased performance. Refer to “CATALYTIC COMBUSTOR

TROUBLESHOOTING” on next page.

• This catalytic heater is equipped with a temperature probe to monitor catalyst operation. Properly

functioning combustors typically maintain temperatures in excess of 500°F (indicated by the thermometer

needle in the active zone), and often reach temperatures in excess of 1000°F. If catalyst temperatures

fall below 500°F (indicated by the thermometer needle in the inactive zone), refer to next step and to

“CATALYTIC COMBUSTOR, TESTING” below.

• You can get an indication of whether the catalyst is working by comparing the amount of smoke leaving the

chimney when the smoke is going through the combustor and catalyst light-off has been achieved, to the

amount of smoke leaving the chimney when smoke is not routed through the combustor (bypass mode):

- Light the appliance as per the lighting instructions (see “LIGHTING THE FIRE”). With smoke routed

through the catalyst, go outside and observe the emissions leaving the chimney.

- Open the bypass mechanism, wait approximately 15 minutes, and again observe the emissions leaving

the chimney. Significantly more smoke will be seen when the exhaust is not routed through the combustor

(bypass mode). Some smoke may be visible shortly after you start the fire and shortly after reloading the

fire. Allow 20 to 30 minutes for the fire to stabilize before making observations.

Содержание BOXER 24




















































Результаты поиска

Содержание BOXER 24

Отзывы:

Blaze King BOXER 24, Руководство по эксплуатации и установке, Страница: 27 / 51

Результаты поиска

Содержание BOXER 24

Отзывы: