manualshive.com logo in svg

Blastrac BMP-E165, Руководство по эксплуатации

Поделиться
Скачать
Blastrac BMP-E165 Скачать руководство пользователя страница 25

 

Operating Instructions                 

BMP-E165

Section 5 – Preparation and 
Starting                                          

April 2006

 

©Blastrac  April 

2006 

24

5.2   Starting 

 

 

If problems occur with the power supply during assembly and/or 
starting, contact a qualified electrician.  Any work performed on 
electrical parts may only be carried out by qualified personnel. 

 

All persons in the vicinity of the machine when it is operating must 
wear protective goggle with side protectors, ear protection and 
safety shoes.  The operator must wear close-fitting protective 
clothing.  All persons in the vicinity of the machine when it is 
operating must wear a respirator. 

 

Before starting the machine, operating personnel must familiarize 
themselves with all the safety instructions in the Manual, specifically 
Section1 “Safety Precautions” 

 

 
 
 
 
The scarifier and the dust collector are now started in the following 
sequence: 
 

a) 

Switch the dust collector on 

 

 

b) 

Using the depth setting adjustment wheel, turn the depth setting 
completely back (counter-clockwise) so that the scarifier drum cannot 
touch the ground when the machine is lowered. 

 
 
 
 
 
 

Содержание BMP-E165





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды