manualshive.com logo in svg

Black Horse Model NOORDUYN NORSEMAN, Инструкция по эксплуатации, Страница: 11 / 18

Поделиться
Скачать
Black Horse Model NOORDUYN NORSEMAN Скачать руководство пользователя страница 11

11

NOORDUYN NORSEMAN           Item code: BH157

.            

 

Instruction Manual

  See pictures below:

ELEVATOR PUSHROD INSTALLATION

  

1)  

Using pliers, carefully make a 90 degree bend 

down at the mark made. Cut off the excess wire, leaving 

about 6mm beyond the blend.

  

2)  

Insert the 90 degree bend down through the 

hole in the servo arm. Install one nylon snap keeper 

over the wire to secure it to the arm. Install the servo 

arm retaining screw.

M2 Lock nut

M2

Bottom side.

Elevator pushrod

Silicone Tube

Cut.

Secure.

Flaslink

Pushrod wire

servo arm

Snap keeper

Elevator servo

Cut.

Bend.

Secure.

Elevator pushrod

IX. RUDDER INSTALLATION

Rudder install as same as the way of aileron. 

RUDDER CONTROL HORN INSTALLATION

Rudder  control  horn  install  as  same  as  method  of 

elevator control horn. 

Top side

Bottom side.

2. Push in

1. A+B Epoxy glue

Control horn 

Содержание NOORDUYN NORSEMAN



















Отзывы:

Нет отзывов