Black Horse Model BH167 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 30

Black Horse Model BH167 Скачать руководство пользователя страница 6

MXS Item code: BH167

Use a covering iron with a

covering  sock  on  hign  heat  to
tighten the covering if necessary.
Apply  pressure  over  sheeted
areas  to  thoroughly  bond  the
covering to the wood.

PREPARATIONS:

2)

Apply drops of thin CA to the top and bottom

of each hinge. Do not use CA accelerator. After

the CA has fully hardened, test the hinges by

pulling on the aileron.

Temporary pin to
keep hinge centered.

1)

Test fit the ailerons to the wing with the hinges. If

the hinges don’t remain centered, stick a pin through
the middle of the hinge to hold it in position.

Secure nylon hinges with instant glue, being
careful not to glue the wing and aileron together.

Align the center line of main wing with aileron.

1

2

Warning!

Make certain the hinges are
adequately secured with glue. if they come loose
in flight accidents may result.

1.

Install the rubber grommets and brass eyelets

onto the aileron servos.

2.

Using a modeling knife, remove the covering

from over the pre-cut servo arm exit hole on the
aileron servo tray / hatch. This hole will allow the

1

2

C.A

C.A

Bottom view

Aileron

INSTALLING THE AILERONS SERVOS.

servo arm to pass through when installing the aileron
pushrods.

3.

Place the servo into the servo tray. Center the

servo within the tray and drill 1.5mm pilot holes
through the block of wood for each of the four
mounting screws provided with the servo.

4.

Using the thread as a guide and using masking

tape, tape the servo lead to the end of the thread:
carefully pull the thread out. When you have pulled
the servo lead out, remove the masking tape and the
servo lead from the thread.

INSTALLING THE AILERONS

6

«
...
4
5
6
7
8
...
»

Содержание BH167































Отзывы:

Нет отзывов