Black+Decker STC5433PC, Руководство пользователя

Страница: 11 / 16

10
ENGLISH (Original instructions)
11
ENGLISH (Original instructions)
Installing and removing the battery pack from the
tool
Warning! Make certain the lock-off button (2) is engaged to
prevent switch actuation before removing or installing battery.
To install battery pack Fig. C)
u
Insert battery (15) into battery housing (15b) until an
audible click is heard (Figure. C)
u
Ensure battery pack is fully seated and fully latched into
position.
To remove battery pack (Fig.D)
u
Depress the battery release button (15a) as shown in
figure D and pull battery pack (15) out of battery housing
(16b).
DUALVOLT 54V Battery Pack (Fig F.)
The DUALVOLT 54V battery pack can be used on 54V &
18V Black+Decker Cordless tools. The battery can recognise
the tool it is inserted into and will run at the relevant power,
providing longer runtime in 18V tools. There is a State of
charge button (15c) which will indicate the level charge at both
54V & 18V.
Setting trimming or edging mode
u
The trimmer can be used in trimming mode as shown
in figure N or in edging mode to trim overhanging grass
along lawn edges and flower beds as shown in figure P.
Trimming mode (FIG. L, M)
For trimming, the trimmer head should be in the position
shown in figure N. If it is not:
u
Remove the battery from the trimmer.
u
Press and hold the head rotate button ( 10 ).
u
While holding the auxillary handle, rotate the head
clockwise.
u
Release the head release button.
u
Lift the edge guide ( 12 ) into the closed position.
Edging mode (FIG. L, M)
Warning! When being used as an Edger, stones, pieces of
metal and other objects can be thrown out at high speed by
the line. The trimmer and guard are designed to reduce the
danger. However, MAKE SURE that other persons and pets
are at least 30m away.Optimum cutting results are achieved
on edges deeper than 50 mm.
For edging, the trimmer head should be in the position shown
in figure P. If it is not:
u
Remove the battery from the trimmer.
u
Press and hold the head rotate button ( 10 ).
u
While holding the auxillary handle, rotate the head
counterclockwise.
u
Release the head release button.
u
Drop the edge guide ( 12 ) to the open position. Ensure
that the edging guide is all the way down, an audible
click will be heard.
u
Do not use this trimmer to create trenches.
u
Using the edge guide (12), guide the trimmer as shown
in figure P.
u
Position the edge guide on the edge of the sidewalk or
abrasive surface so the cutting line is over the grass or
dirt area to be edged.
u
To make a closer cut, slightly tilt the trimmer.
Operation
Warning! To reduce the risk of serious personal injury,
turn unit off and remove the battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Warning! Always use proper eye protection.
Caution: Before you begin trimming, only use the appropriate
type of cutting line - 2.0mm diameter, ROUND nylon line.
Caution: Inspect area to be trimmed and
remove any wire, cord, or string-like objects which could
become entangled in the rotating line or spool. Be particularly
careful to avoid any wire which might be bent outwardly into
the path of the appliance, such as barbs at the base of a chain
link fence.
Proper hand position
Warning! To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown in figure O.
Proper hand position requires one hand on the main handle
(3) and one hand on the auxiliary handle ( 6 ).
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Switching on and off
u
To switch the trimmer on, press in and hold the lock
off button (2), depress the variable speed trigger (1).
The trimmer’s speed, power, and runtime depend on
how far you press the switch. Lightly depressing the
trigger will result in lower speed and power, but longer
runtime. Fully depressing the trigger will result in
maximum speed and power, but shorter runtime.
u
To switch the trimmer off, release both the trigger and
the lock off button.
Warning! Never attempt to lock the on/off button in the on
position.
Operating the trimmer
u
With the unit on, angle unit and slowly swing the
trimmer side to side as shown in figure N.
u
Maintain a cutting angle of 5° to 10°.