10
ENGLISH
(Original instructions)
Assembly
Warning!
To reduce the risk of serious personal injury, turn
unit off and remove the battery pack before making any
adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Assembly tools required
u
Phillips Screwdriver (not supplied).
u
Hex wrench (supplied).
Installing the guard
Warning!
Never operate appliance without the guard (13)
firmly in place. The guard must always be properly attached
on the appliance to protect the user.
u
Remove the screw from the guard.
u
Turn the trimmer upside down so that you are looking
down at the spool cap ( 20 ).
u
Turn the guard (12) upside down and slide it fully onto the
trimmer head (10). Make sure the tabs ( 16 ) on the guard
engage the ribs (17) on the trimmer head as shown.
u
Continue to slide the guard on until you hear it “snap”
into place. The locking tab (18) should snap into the
housing slot (19) as shown in figure G.
u
Using a phillips screwdriver, insert the guard screw and
tighten securely as shown in figure H to complete the
guard assembly.
u
Once the guard is installed, remove the covering from
the line cut-off blade, located on the edge of the guard.
Assembling the Pole
u
To assemble the pole, line up the upper trimmer pole
(6) and the lower trimmer pole (7) as shown in figure I.
Press down the latching button (20) and slide the upper
pole into the lower pole. Ensure the latching button
engages the latch hole (21).
u
Secure the poles by tightening the middle bolt (22) with
the supplied hex wrench (23) as shown in figure J.
Attaching the auxiliary handle
u
Place the auxiliary handle (5) onto the top of the upper
trimmer pole (6) as shown in figure K.
u
Slide the bracket (24) of the auxiliary handle onto the
bottom of the handle.
u
Thread the handle bolts (25) through the handle and
into the bracket from above.
u
Tighten the handle bolts. Ensure the handle is securely
attached by closing the handle clamp (26).
u
To adjust the position of the auxiliary handle, open the
handle clamp and slide the handle up and down the
pole until it is in the desired location. Close the clamp to
lock the handle in place.
Releasing the cutting line
For shipping purposes, the cutting line is taped to the spool
housing.
u
Remove the tape holding the cutting line to the spool
housing. See "Replacing the Spool" for instructions for
removing the spool.
Charging procedure (STC5433 unit only)
BLACK+DECKER chargers are designed to charge
BLACK+DECKER battery packs.
u
Plug the charger (15) into an appropriate outlet before
inserting the battery pack (14).
u
Insert the battery pack (14) into the charger (15) as shown
in figure A.
u
The green LED (15a) will flash indicating that the battery is
being charged.
u
The completion of charge is indicated by the green LED
(15a) remaining on continuously. The pack is fully charged
and may be used at this time or left on the charger.
Note:
Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished. For longest
battery life, do not discharge batteries fully.
It is recommended that the batteries be recharged after each
use.
Leaving the battery in the charger
The charger (15) and battery pack (14) can be left connected
with the LED glowing indefinitely. The charger will keep the
battery pack fresh and fully charged.
Important charging notes
u
Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65°F and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
u
The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack
in a warm environment such as in a metal shed, or an
uninsulated trailer.
u
If the battery pack does not charge properly:
u
Check current at receptacle by plugging in a lamp or
other appliance.
u
Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
u
Move charger and battery pack to a location where the
surrounding air temperature is approximately 65°F
- 75°F (18°- 24°C).
u
If charging problems persist, take the tool, battery pack
and charger to your local service center.
Содержание STC5433
