Black+Decker PRH5BCA, Инструкция по эксплуатации

Страница: 8 / 20

7
12V DC PORTABLE POWER SUPPLY
The 12 volt DC accessory outlet is located under a protective cover on the right hand side of the front panel (refer to the Features section to locate). This
portable power source is for use with all 12 volt DC accessories equipped with a male accessory outlet plug that are rated up to 5 amps.
1. Lift up the cover of the unit ‘s 12 volt DC outlet.
2. Insert the 12 volt DC plug from the appliance into the 12 volt accessory outlet on the unit. DO NOT EXCEED A 5 AMP LOAD.
3. Switch on the appliance and operate as usual.
4. Periodically check the unit’s battery status by pressing the battery power level button. (Two red and one green battery status indicator lights indicate a full
battery. Only one red battery status indicator lights indicates that the unit needs to be recharged.)
USB POWER PORT
The USB power port is under the same protective cover as the 12 volt DC outlet at the left hand side of the front panel (refer to the Features section to locate).
1. Push the USB Power Button to turn the USB Port on and the USB power indicator will light.
2. Lift up the cover of the USB Charging Port.
3. Plug the USB-powered device into the USB Charging Port and operate normally.
4. Periodically check the unit’s battery status by pressing the battery power level button. (Two red and one green battery status indicator lights indicate a full
battery. Only one red battery status indicator lights indicates that the unit needs to be recharged.)
Notes:
This unit's USB charging port does not support data communication. It only provides 5 volts/2,000 mA DC power to an external USB-powered device.
Some USB-powered household electronics may not operate with this USB charging/power port. Check the manual of the corresponding electronic device to confirm that it can be used with
this type of USB charging/power port.
Make sure the USB power button is turned off when the unit is being recharged or stored.
AREA LIGHT
The built-in 3-LED area light located on the back of the unit is controlled by the area light power button on the front panel (refer to the Features section to
locate). Press the area light on/off button once to turn the light on. Press the area light power button again to turn the area light off.
Periodically check the unit’s battery status by pressing the battery power level button. (Two red and one green battery status indicator lights indicate a full
battery. Only one red battery status indicator lights indicates that the unit needs to be recharged.)
Note:
Make sure the area light and the unit are turned off when the unit is being recharged or stored.
PORTABLE COMPRESSOR
The built-in 12 volt DC compressor is the ultimate compressor for all vehicle tires, trailer tires and recreational inflatables. The compressor hose with Sure Fit
®
nozzle is stored in the compressor hose storage compartment. The compressor on/off switch is located on the front panel of the unit to the right of the air
pressure gage (refer to the Features section to locate). The compressor can operate long enough to fill up to 3 average sized tires before the battery must be
recharged.
The compressor may be used by removing the air hose from the storage hatch and if required, fitting the nozzle adapter to the air hose. Return the hose to the
storage compartment after use.
WARNING – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: follow all safety instructions found in the “Specific Safety Instructions for
Compressors” section of this instruction manual.
Inflating Tires or Products With Valve Stems
1. Screw the Sure Fit
®
nozzle onto the valve stem. Do not overtighten.
2. Turn on the compressor power switch.
3. Check pressure with the pressure gauge.
4. When desired pressure is reached, turn off the compressor power switch.
5. Unscrew and remove the Sure Fit
®
nozzle from the valve stem.
6. Allow the unit to cool, then recharge before storing away.
7. Store the compressor hose and nozzle in the storage compartment.
Inflating Other Inflatables Without Valve Stems
Inflation of other items requires use of the nozzle adapter.
1. Screw the nozzle adapter into the Sure Fit
®
nozzle. Do not overtighten.
2. Insert the adapter into item to be inflated.
3. Turn on the compressor power switch – inflate to desired pressure or fullness.
IMPORTANT NOTE:
Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not over-inflate.
4. When desired pressure or fullness is reached, turn off the Compressor Power Switch.
5. Disconnect the nozzle adapter from the inflated item.
6. Unscrew and remove the nozzle adapter from the Sure Fit
®
nozzle.
7. Allow the unit to cool, then recharge before storing away.
8. Store the compressor hose, nozzle and nozzle adapter in the storage compartment.
TROUBLESHOOTING
Problem Solution
Unit will not charge
• Make sure the inverter power switch is in the off position.
• Make sure a suitable gage extension cord is properly connected to both the unit and a functioning AC outlet.
or
• Make sure the 12V DC charger is properly connected to both the unit and a functioning DC power source.
Unit fails to jump-start
• Make sure unit’s jump-starter power switch is in the on position.
• Check that unit has a full charge. Recharge unit if necessary.
• Make sure a proper polarity cable connection has been established.
120V AC outlet will not power
appliance
• Make sure the inverter power switch is in the on position.
• Make sure you have followed all the steps in the 120V AC portable power supply instructions carefully. Refer to the
important notes included in that section that explain common problems and solutions.
• Check that unit has a full charge. Recharge unit if necessary.
12V DC accessory outlet will not
power appliance
• Make sure the the appliance does not draw more than 5 amps.
• Check that unit has a full charge. Recharge unit if necessary.