Black+Decker EBCD703, Руководство пользователя

Страница: 8 / 17

8
ENGLSIH
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
u
Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
u
Keep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
u
Make sure switch turns drill on and off.
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulfurized cutting oil or lard oil.
Screwdriving
u
Always use the correct type and size of screwdriver bit.
u
amount of washing liquid or soap as a lubricant.
u
Always hold the tool and screwdriver bit in a straight line
with the screw
8
ENGLISH (Original instructions)
Troubleshooting
Problem Possible cause Possible solution
Unit will not start. Battery pack not
charged.
Check battery pack charg-
ing requirements
Battery pack will not
charge.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Unit shuts off
abruptly.
Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries accord-
ing to local provisions. Further information is available at
www.2helpU.com
Technical data
EBCD703
Voltage V
DC
18V (20V Max)
No-load speed Min
-1
Nm 38
0-360/ 0-1400
Chuck capacity mm
1-10
Max Drilling capacity
Steel/wood mm
Weight kg
0.9
10/25
Charger
Input voltage V
AC
220 220 220
Output voltage V
DC
2 4 18
Current 400mA 1A
Approx. charge
time
Hours 4-5 1.5-2
18
2A
0.5-1
Battery
BL2018* BL1518*
Voltage V
AC
20
20
Capacity Ah
2.0
1.5
Type
Li-Ion
Li-Ion
6
ENGLISH (Original instructions)
9
ENGLISH (Original instructions)
9
ENGLISH (Original instructions)
Service Information
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the BLACK+DECKER location
nearest to you.
Note
u
BLACK+DECKER's policy is one of continuous improve-
ment to our products and, as such, we reserve the right to
u
Standard equipment and accessories may vary by country.
u
u
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER dealers for
range availability.