8
ENGLISH
(Original instructions)
2. Wall mounted battery charging
u
Mark the location of the charging station (5a) screw holes
on the wall (within reach of an electrical outlet) for
charging the vacuum while it is on the charging station.
u
Fix the charging station (5a) to the wall using
appropriate screws and plugs for the type of wall, and
weight of the appliance.
u
Install the cup charger (5) into the charging station (5a).
Ensure it is locked into place before proceeding.
Note:
To remove the cup charger from the charging
base pull out on the retaining tabs and lift the cup
charger out.
u
Plug the charger into an appropriate outlet before
inserting the battery pack.
u
Slide the battery pack onto the charging station.
3. Wall mounted vacuum storage and battery
charging
The product can be attached to a wall to provide a
convenient storage and charging point for the appliance.
When mounting to a wall, make sure the mounting method
is suitable for the wall type and is appropriate to the weight
of the appliance.
u
Mark the location of the charging station screw holes on
the wall (within reach of an electrical outlet for charging
the vacuum while it is on the charging station.
u
Fix the charging station to the wall using appropriate
screws and plugs for the type of wall, and weight of the
appliance.
u
Install the cup charger into the charging station. Ensure
it is locked into place before proceeding.
Note:
To remove the cup charger from the charging base pull
out on the retaining tabs and lift the cup charger out.
u
Plug the charger into an appropriate outlet.
u
With the battery installed on the vacuum, slide the charge
port (14), located on the vacuum base, onto the
rails of the charging station (5a).
u
The white LED (3) on the vacuum will flash indicating that
the battery is being charged.
u
The LED sections increase as the battery is charged - when
fully charged the LEDS go out. The pack is fully charged
and may be used at this time or left on the charger.
Leaving the battery in the charger
The charger and battery pack can be left connected with
the green LED glowing indefinitely. The charger will keep
the battery pack fresh and fully charged.
To install battery pack (fig. B)
u
Insert battery (4) into tool until an audible click is heard as
shown in figure B.
u
Ensure battery pack is fully seated and fully latched into
position.
To remove battery pack
u
Depress the battery release button and pull battery pack
(4) out of the tool.
Assembly (Fig. C)
u
Align the top of the extension tube (9) with the vacuum
inlet (15) as shown in figure C.
u
Push the extension tube (9) onto the vacuum inlet (15) so
it locks into position.
u
Align the bottom of the extension tube (9) with the floor
head (8) as shown in figure C.
u
Push the bottom of the extension tube (9) onto the floor
head (8) so it locks into position.
u
To remove an accessory, press the accessory release
latch located on the accessory and pull it off.
USE
This vacuum cleaner can be used in one of four ways.
u
With the extension tube (9) and the floor brush (8) as
shown in figure C.
u
With the floor brush (8) and the vacuum inlet (16) as
shown in figure D.
u
With the extension tube (9) and an accesssory tool (10),
(11) or (13) as shown in figure E.
u
With an accesssory tool (10), (11) or (13) and the
vacuum inlet (15) as shown in figure E.
u
Accessories not supplied with your unit can be ordered
through service department.
Switching ON and OFF (Fig. F)
u
To switch ON, press the On/Off button (1).
u
For increased power, slide the variable power switch (2)
forward.
Note:
The floor brush (8) will power on when it is
attached to the vacuum or extension tube (it can be switched
off by pressing the button 2a on the display). The LED
worklights on the front of the floor head will illuminate
whenever the beater bar activation button (2a) is switched ON
(they can be switched off by pressing the button again).
Note:
The state of charge indicator LEDs (3) will
illuminate while the vacuum is ON or during the charging
process.
u
To switch OFF, press the On/Off button (1).
u
Return the product to the charger immediately after use
so that it will be ready and fully charged for the next use.
Ensure that the product is fully engaged with the charger
plug.
Using an Accessory tool (Fig. G)
Your vacuum may come with some of the following tools.
u
2 in 1 Accesssory tool (10)
u
Crevice tool (11).
u
Wide mouth dust brush (13).
u
The accessory tool (10), (11) or (13) can be fitted either
