Black Box MT210A Скачать руководство пользователя страница 9

Страница: 9 / 46

MULTIPORT CSU/DSU

1. Specifications

Compatibility

—AT&T 62310

DDS Line Interface

—Externally accessible RJ-48 female

Transmission Format

—Synchronous or asynchronous

Transmission Line

—Two unconditioned twisted pair

Clock Options

—Internal, external, receive loopback, and campus

Interfaces

—Modules: RS-232 (DB25 female), RS-422/530 (DB25 female), V.35

(M/34 female), X.21 (DB15), G.703 (RJ-45), Ethernet Bridge

Speeds

—Synchronous: 2.4, 4.8, 9.6, 19.2, 56, and 64 kbps; Asynchronous: 2.4,

4.8, 9.6, 19.2, 38.4, and 57.6 kbps

Diagnostics

—V.54-compliant local and remote loopbacks; V.52-compliant 511

and 2047 BER tests

Indicators

—Front-panel LEDs: DDS line rates (2.4, 4.8, 9.6, 19.2, 38.4, and 57.6

kbps), Power, TD, RD, RTS, CTS, DCD, DSR, DTR, No Signal, Test Mode,
Error Indication

Distance

— -49 dBm receiver sensitivity or better

RTS/CTS Delay

—0 ms/50 ms

Front-Panel Switches

—Loopback indication and Bit Error Rate Test

Temperature Range

—32 to 122 °F (0 to 50 °C)

Altitude

—Up to 15,000 feet (4572 m)

Humidity

—5 to 95% noncondensing

Surge Protection

—600 W Power Dissipation

Lightning Protection

—Gas Tube

Isolation

—1500 V via isolation transformers

Approvals

—FCC Part 68, FCC Part 15, Class A, CE marked per EMC Directive

89/336/EEC and Low Voltage Directive 73/23/EEC, UL and cUL safety
approvals

Содержание MT210A














































Результаты поиска

Содержание MT210A

Отзывы:

Похожие инструкции для MT210A

Бренды по названию

Популярные бренды

Black Box MT210A, Руководство пользователя

Результаты поиска

Содержание MT210A

Отзывы:

Похожие инструкции для MT210A

Бренды по названию

Популярные бренды