background image

 

5

 

1.3  FCC PART 68 

 

This equipment complies with Part 68 of the FCC Rules. Please note the 
following:

  

be

fore y

 

The required Universal Service Order code (USOC) 

jack: RJ-11C

The REN helps you determine the number of devices you can con-
nect to your telephone line and still have all of those devices ring 
when your number is called. In most, but not all, areas, the sum of 
the RENs of all devices should not exceed five (5.0). To be certain of 
the number of devices you can connect to your line, you should call 
your local telephone company to determine the maximum REN.

The Facility Interface Code: 

 

02LS2

 

The Service Order Code(s) (SOC): 

 

9.0F

 

REN No.: 

 

0.2

 

   2. Your telephone company may make changes to its facilities, equip-

ment, operations, or procedures that could affect the proper func-
tioning of your equipment. The telephone company will notify in 
advance of such changes to give you an opportunity to maintain 
uninterrupted telephone service.

 

Caution

 

The Model 

ME0011A-vDSL

 is not intended to be 

connected to the public

 telephone network.

 

 

 
 
 

Содержание ME0010A-VDSL






















Отзывы: